Question about Subaru Impreza

Open Question

Impreza lunges and stalls when put into drive or reverse

Idles high jumps and dies

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

taran_2005
  • 10515 Answers

SOURCE: 94 Jeep Wrangler intermittently stalls when put in reverse, drive

Take the air inlet hose off where it enters the throttle body and take a look at the throttle plates. It is likely that they’re dirty and have a build-up of carbon deposits. That is the most common cause for stalling that we see in the shop for your vehicle. Sometimes all it takes is a good cleaning to cure the stalling problem. There is an idle speed setting on your Jeep, but to check and/or perform this service step requires the use of a computer scan tool for your vehicle. If the cleaning doesn’t help ask a repair facility to check and reset, if needed, the minimum idle speed on your Jeep.


Thnx.

Posted on Nov 27, 2008

  • 1 Answer

SOURCE: 1995 pontiac bonneville stalls

I just went through lots of troubleshooting and expense on my 1996. Whenever I would lift my foot off the accelerator and was below about 30 mph, the rpm's would starts jumping around and sometimes it would stall. If I gave it a little gas (accelerator), I could sometimes keep it running. It also backfired once in a while. Starts right back up. Also, if I let it idle while in part, it would die after 1-2 minutes.

I ended up finding a hole in the fuel regulator. About a ~$70 part if you get an AC Delco, but very simple to change.

Posted on Dec 24, 2008

  • 1 Answer

SOURCE: 1991 ford probe

duck tape on the air intake. I just fixed mine. There is a crack on the intake that lets too much air in when you put it in drive that makes the car stall. Try it it works.

Posted on Dec 24, 2008

mecanica03
  • 881 Answers

SOURCE: 1993 camry has full engine power in reverse, but not in drive

YOU MUST CHECK IF THE OIL LEVEL IN TRANSMISSION ,THE PROBLEM IS NOT THE INGINE

Posted on Apr 12, 2009

  • 4 Answers

SOURCE: My 2004 5.4L FX4 F150 is stalling out when I get

I'd check the idle air control motor.... replace it. I have ssen lots of Fords have this issue

Posted on Jul 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After ideling a while i try to shift into reverse or to drive and it always dies .......any tips or ideas?


engine dies when shifting into reverse or drive - Third Generation ...

www.thirdgen.org/forums/tbi/346079-engine-dies-when-shifting.html
Feb 11, 2006 - engine dies when shifting into reverse or drive ... After it dies it starts right up and idles fine in park or neutral. ... these ignition items because you weretrying to cure the stalling, or, did the stalling occur after you replaced these items? ...The only thing that kept the car running was adjusting the Idle screw up.

Engine Dies When Placed In Gear***Split from Spittybug...EFI ...

dmctalk.org > ... > MAIN FORUMS > Custom DeLoreans/Mods > EFI

Jul 5, 2012 - 18 posts - ‎4 authors
Just to give an update on my car - I've been having an issue with the car stalling when moving from Park into Reverse or Drive (I have automatic). ... I have been playing with the idle advance trying to get more ... I put in the remainder of the AT fluid I had on hand and the car never died on shifting after that.

starts but dies when shifted into drive or reverse - Suzuki Forum


Jan 26, 2016 | Cars & Trucks

2 Answers

My 1993 Toyota Corolla stalls and will not stay running.


If changing the battery does not solve problem, or only solves it until the battery dies then have the alternator tested. I have noticed on several occasions with a couple of my vehicles that at times of very high moisture in the air they do not stay running, once the humidity goes down they are fine.

Apr 01, 2014 | 1993 Toyota Corolla

1 Answer

Just replaced heater core, now car dies when put in gear


check for pinch wires around core install. also a vacume leak from same job not plugged

Dec 03, 2013 | 1998 Mercury Grand Marquis

1 Answer

What causes my 1996 poniac sunfireto stall out when it goes in reverse or drive?


Is the check engine light on when it is running ?
Can you press on the gas pedal and keep it running ?
Could be the torque converter, a failing air control valve, dirty throttle body, or other things.

Jul 03, 2012 | Pontiac Sunfire Cars & Trucks

1 Answer

Dies when i put it in drive or reverse


knowing pontiacs it's either something with the electrical system, or the transmission.

May 20, 2012 | 1997 Pontiac Grand Prix

1 Answer

I have a 2005 venture and stalls when put in reverse and drive what could it be


Could be the torque converter clutch solenoid. I'm not sure of the exact syptom other than I know it dies. Does it jump at all then the engine dies as if the load from the engine is causing it to stall ?

May 17, 2012 | 2005 Chevrolet Venture

3 Answers

Idles fine then dies when put in drive or reverse


You may have a problem with idle speed control motor or ETC as GM calles it. here is a photo and a price from rockauto.com.
STANDARD MOTOR PRODUCTS Part # SA4 moreinfo.gif
Motor Assembly sa4_full.jpg $110.99

Apr 18, 2009 | 1990 Cadillac Fleetwood

1 Answer

1991 ford probe


duck tape on the air intake. I just fixed mine. There is a crack on the intake that lets too much air in when you put it in drive that makes the car stall. Try it it works.

Nov 23, 2008 | 1990 Ford Probe

1 Answer

A Jumping or lunging problem.


Have you checked all your mounts to make sure none are broken?

Oct 24, 2008 | 1988 Plymouth Reliant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...