Question about Cars & Trucks

Open Question

Removing door panel on c4 picasso

Driver side door panel needs to be removed to fit electric window regulator.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 42 Answers

SOURCE: 1991 Nissan Maxima: Removal of front driver side door panel

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Posted on Mar 20, 2009

Ad
  • 119 Answers

SOURCE: want to remove driver side door panel to gain access to power window motor

first remove the tweeter speker if equipped this comes off easily by gently prying from behind, then remove the small panel behind pull handle you"ll find a screw behind it\remove that,the next part is a little tricky the door grip needs to come off to achieve this place a small flat screwdriver at the top of the handle and pry forward the turn handle counterclockwise and this will release it from the clips you"ll then find 2 screws one at the top other at the bottom of door grip remove those and then gently pry from the bottom of the door panel to release the retaining clips thats it

Posted on Jul 14, 2009

  • 1986 Answers

SOURCE: need directions to remove driver door interior panel 1997 deville

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: 2000 Saturn SL2 driver's side

Fore remove the door panel in a SL2, you have to take off the door handle. You have to disengage the door locking mechanism from the door handle, then unscrew the panel and take it off.

The door handle unhinges from the locks and from the window controls. If your windows are electric, just unsnap the cord attached and leave it hanging out.

You may have to work with the door handle as it won't come out of the slot very easily and you don't have a lot of room. A flat bladed screwdriver with a long metal piece should work to unsnap it.


ION, L-Series, S-Series 1999-2005 - Window Systems

Door Glass & Regulator
Power Windows
Diagnosis & Testing
Driver's Window Switch

  1. Turn the ignition OFF, disconnect the harness connector at the driver window switch.
  2. Test for infinite resistance between the signal terminals A and B and the B+ circuit terminal E with the passenger window switch in the INACTIVE position. If less than infinite resistance, replace the driver window switch.
  3. Test for less than 2 ohms of resistance between the signal terminal A and the B+ circuit terminal E with the passenger window switch in the UP position. If greater than 2 ohms, replace the driver window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal B and the B+ circuit terminal E with the passenger window switch in the DOWN position. If greater than 2 ohms, replace the driver window switch.
  5. Test for infinite resistance between the signal terminals F and H and the B+ circuit terminal E with the driver window switch in the INACTIVE position. If less than infinite resistance, replace the driver window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal E with the driver window switch in the UP position. If greater than 2 ohms, replace the driver window switch
  7. Test for less than 2 ohms of resistance between the signal terminal H and the B+ circuit terminal E with the driver window switch in the DOWN position. If greater than 2 ohms, replace the driver window switch.
Passenger's Window Switch
  1. Turn the ignition OFF, disconnect the harness connector at the passenger window switch. Test for infinite resistance between the signal terminals G and F and the B+ circuit terminal with the switch in the INACTIVE position. If less than infinite resistance, replace the switch.
  2. Test for less than 2 ohms of resistance between the signal terminal G and the B+ circuit terminal with the switch in the UP position. If greater than 2 ohms, replace the switch.
  3. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal with the switch in the DOWN position. If greater than 2 ohms, replace the switch.
Window Motor
  1. Install a 30-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The motor should perform the UP or DOWN function.
  2. If the function does not perform as specified, replace the motor.
  3. Reverse the jumper wires; the motor should perform the DOWN or UP function.
  4. If the function does not perform as specified, replace the motor.
Removal & Installation
Window Motor & Regulator
  1. Raise the window to the full UP position.
  2. Remove the upper trim panel.
  3. Remove the manual window regulator handle, if equipped.
  4. Remove the power door lock switch, if equipped.
  5. Remove the pull cup assembly.
  6. Remove the door trim push-in retainers.
  7. Remove the screw from the trim panel.
  8. Pull the bottom of the door trim out to disengage the clips.
  9. Lift up on the door trim panel to disengage the inner belt molding from the door flange.
  10. Remove the door trim panel.
  11. Remove the radio speaker.
  12. Remove the front door water deflector.
  13. Disengage the door glass to the regulator sash channel clips. Separate the door glass from the sash channel.
  14. Push the window to the up position and tape in place.
  15. Loosen the power window regulator bolts.
  16. Remove the rear regulator bolt.
  17. Lift the window regulator, disengaging the loosened bolts from the door.
  18. Disconnect the regulator electrical connector.
  19. Remove the power window regulator from the door.
To install:
  1. Installation is the reverse of removal.
Window Switch
  1. Using a flat-bladed tool, pry the switch from the door trim panel enough to expose the locking tabs.
  2. Press the locking tab to remove the switch from the door trim panel.
  3. Disconnect the electrical connector.
  4. Remove the switch.
To install:
  1. Installation is the reverse of removal.

I hope helped with this; good luck.

Posted on Oct 21, 2009

  • 2 Answers

SOURCE: X5 Door Panel Removal

there are 4 torx T-15 screws, one in the rear map pocket, one under the air bag logo plastic clip, one under the wood trim (pry the trim off carefully), and one holding the door handle assembly (also revealed when you remove the wood burl cover). Pick up a pry tool at autozone, about 5 bucks to pry the clips out without breaking

Posted on Nov 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove interior door panel 2002 Chevy tracker


No you don't need any special tool . Find all screws on out side of door trim panel and the window handle , the mirror cover plate , then just pull on edge of the panel .
Gently pry the front side door trim panel (3) from the front side door by disengaging the plastic retainers which secure the panel.
Position the door trim panel (3) away from the door in order to gain access to the front side window switch electrical connector, if equipped.
Disconnect the window switch electrical connector, if equipped.
Remove the door trim panel (3) from the vehicle.
Remove the front side window switch from the door trim panel (3) by releasing the 4 plastic retaining tabs, as needed.

Use a cloth in order to pull off the snap ring which secures the front side door window regulator handle (1), if equipped.
Remove the window regulator handle (1), if equipped.
Remove the front side master window switch, if equipped. Refer to Power Accessory Switch Panel Replacement .

Remove the front side door inside handle (1). Refer to Front Side Door Inside Handle Replacement .
Remove the outside rearview mirror opening cover (2).
Remove the screw which secures the front side door pull handle (4).

Front Side Door Inside Handle Replacement
Removal Procedure
Remove the screw which secures the front side door inside handle (1).
Slide the inside handle (1) forward in order to release the retaining tabs which secure the handle to the door.
Open the front side door inside handle rod retainer and remove the front side door inside handle rod from the inside handle (1).
Remove the inside handle (1) from the vehicle.

Check out youtube video showing how to do it !
How To Remove Install Front Door Panel Suzuki XL 7

Jun 10, 2017 | Cars & Trucks

1 Answer

How do I remove door panel on 87 C4 Vette


to remove door trim you have to disconnect negative battery cable.then remove two screws attaching arm rest to door trim.remove arm rest it held in place by front and rear hooks that fit into slots in door trim.to release the hooks grasp the arm rest with both hands push it towards thr door pull up on the side of the arm rest facing door.remove four speaker grille mounting screws and the grille.then remove door trim panel screwss from bottom edge of the panel.remove the three remote control plate screws from the plate and the single screw in the rear edge of the door.then lift up on the door trim panel to release the molding from the top edge of the door then slide the panel forward to clear the latch release handle and down to clear the lock rod knob.if job look to difficult let a body shop fix.removing window door motor need tools to drill out rivets and reinstall rivots you need special tools to fix window motor and regulator.

Apr 14, 2013 | 1987 Chevrolet Corvette

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How to remove the window driver side of toyota corrola 1988


Door Glass and Regulator - REMOVAL & INSTALLATION
Front Door
  1. Disconnect the negative battery cable.
  2. Remove the front door panel to gain access to the regulator assembly.
  3. Remove the service hole cover.
  4. Lower the regulator until the door glass is in the fully open position.
  5. Remove the two glass channel mount bolts.
  6. Pull the glass up and out of the door.
  7. Unbolt and remove the inside door panel frame if so equipped.
  8. If equipped with power windows, disconnect the electrical connector.
  9. Remove the equalizer arm bracket mounting bolts.
  10. Remove the window regulator mounting bolts and the regulator (with the power window motor attached) through the service hole.
To install:
  1. Coat all the window regulator sliding surfaces with multi-purpose grease.
  2. Place the regulator (with the power window motor) through the service hole and secure with the mounting bolts. tighten the bolts to 48 inch lbs. (5 Nm). Attach the power window harness if equipped.
  3. Place the door glass into the door cavity.
  4. Connect the glass to the regulator with the channel mount bolts.
  5. With the equalizer arm, raise the glass to the almost closed position and make sure that the leading and trailing edges of the glass are equally distant from the top of the glass channel. If not, adjust the equalizer arm to achieve an even fit.
  6. Install the service hole cover.
  7. Install the door panel and reconnect the negative battery cable. Check window and door for proper operation.

Hope helps (remember rated and comment this).

Aug 25, 2010 | 1988 Toyota Corolla 4 Door

1 Answer

How to remove drivers door panel on 1999 ford escort. I need to repair the windows switch for the drivers side. My window is in the down position and won't come up when I push the button. All other windows...


Remove the front door pull cup screw 1152a96.gif

Remove the screw cap and the screw from the inside door handle and slide the handle rearward to disengage the hook from the inner sheet metal.
  • Disconnect the inside door handle from the front door latch remote control link
37470b2.gif

Remove the two-piece pushpins from the front door trim panel (23942).
2a1605a.gif

NOTE: Use a commonly available spring loaded trim pad removing tool with a long thin nose to prevent damage to the door trim panel.
Release the seven front door trim panel bullet nose fasteners and push inboard, then upward to release the front door trim panel.
  • If equipped, disconnect the master window regulator control switch electrical connector
cc0d2af.gif

Remove the retainer from the master window regulator control switch panel.
  1. Pull outward on the cup retainer tabs and remove.
  1. Remove the master window regulator control switch electrical connector from the retainer
ab8ff6c.gif

Jun 05, 2010 | 1999 Ford Escort

1 Answer

Rear electric window will notwork


Yes . Remove door panel, switch connectors and plastic protective covering on the door. have a helper pull the windw up while you measure the distance from bottom of window regulator to bottom of door panel.
(approx 8-12"), cut a block of wood that will fit between the bottom of the regulator to bottom of door panel wedge it threw the opening in the door a place it between the regulator and door bottom. Wood is soft and sturdy and should hold up until you get the window fixed.
Can the driver control panel switch make that window work. If the answer is No then the problem is the motor on that side. If the answer is yes then the problem is the switch on that window. by the way if the driver control panel gets the window to rise Merry Christmas you don't need the wooden block.

May 05, 2010 | 1997 Plymouth Grand Voyager

2 Answers

I need help with replacing the driver side window in a 2003 ford f-150,four door super crew cab truck.


Removal & Installation
Motor - Front Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch
  3. Remove the front door trim panel and watershield.
  4. Tape the window in the full UP position.
  5. Disconnect the window motor electrical connector.
    NOTE Support the window motor while removing the window motor retaining screws.
  6. Remove the window motor bolts and remove the motor.
  7. To install, reverse the removal procedure.
Rear Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the rear door trim panel and the rear door trim watershield.
  4. Remove the door speakers.
  5. Tape the window glass in the full UP position.
  6. Disconnect the window regulator electric drive.
  7. Position the connector for the window regulator electric drive inside of the door.
  8. Remove the bolts.
  9. Separate the window regulator electric drive from the rear door window regulator.
  10. Remove the window regulator electric drive from the door.
  11. To install, reverse the removal procedure.

Motor & Regulator

3d4a07e.jpg

Fig. Front Door Trim Panel

7932e42.jpg


Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows

506866e.jpg

Fig. Window regulator arm nuts


db15984.jpg

Fig. Window regulator bolts

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the door trim panel.
  4. Remove the door speaker.
  5. Remove the door watershield.
    NOTE Do not remove the window glass from the door.
  6. Remove the window glass from the window regulator.
  7. Tape the window glass in the full UP position.
  8. Disconnect the window motor electrical connector (power windows only).
  9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
  10. Loosen the bolts and remove the window regulator.
  11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

Nov 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

HOW DO I REPLACE THE DRIVER SIDE POWER MIRROR ON AN 98 F-150?


Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

Jan 31, 2009 | 1997 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...