Question about 1992 Toyota Celica

Open Question

2002 Ford Windstar Van 3.8 eng. I need a diagram for engine & trans mounts.

My Haynes manual shows them but the pictures are so vague I can't make them out.

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15467 Answers

SOURCE: Picture of Sealant RTV Locations 1.8L

If you replaced the gasket,you dont need RTV sealant, be careful how tight you make those bolts. 10 INCH pounds is enough! Not foot lbs!!!

Posted on May 01, 2013

Testimonial: "Hi. Haynes says there are 5 areas on the engine edges around caps or something that require (not optional) RTV for the install not to leak. This is whether or not you use anything on the gasket itself."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 windstar transmission schematic


I am assuming you need a schematic for this and that you've check all of the other more common things like broken linkages, low transmission fluid, etc. Other than the wiring diagrams that are found in the Haynes or Chiltons manuals, you would have to get a service manual from a dealer.There just isn't much electrical inside a transmission though that isn't covered in the wiring diagrams found in these manuals,which can be found at your local parts store.

Nov 21, 2011 | 2002 Ford Windstar Cargo

1 Answer

Rear heater core is leaking


YOU NEED A HAYNES REPAIR MANUAL FOR DIAGRAM AND INSTRUCTION HOW TO REMOVE INSTRUMENT PANEL SUPPORT BRACKETS AND HEATER MAIN FLOOR DUCT.HARD JOB WITH OUT MANUAL.

May 05, 2010 | 1998 Ford Windstar

1 Answer

Replacing tension wheel on drivebelt


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 1998 Ford Windstar with either the 3.0L or 3.8L V6 Engine.
These have the Diagrams of the variety of Tensioners that are used. NOTE: Most of the Tensioners have three (3) bolts that mounts the Tensioner Assembly to the Engine. After removing the Belt: Remove the three (3) Bolts and remove the Tensioner.
http://www.2carpros.com/car_repair_information/year/1998/make/ford/model/windstar/1998_ford_windstar_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Dec 17, 2009 | 1998 Ford Windstar

1 Answer

Just need to open door in heater box to get hot


it sound asd if its stuck give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local ford dealership and in the parts department they be able to get you picture and diagram showing you how to repair it if all fails stop by your local library and get your hands on a Haynes auto repair Manual for you van wish you the best of luck Michigan Man.

Oct 22, 2009 | 1999 Ford Windstar

1 Answer

Replacing flywheel


you may have to remove the transmission not the engine and give this website a try www.alldatadiy.com to see if they have your car listed if they do you be able to get pictures and diagrams showing you how to repair your car also checkout your local library for a Haynes repair manual for your van and you can checkout this website also www.autozone.com if they have you van listed you be able to checkout a price i hope i have been some help to you Michigan Man.

May 21, 2009 | 1999 Ford Windstar

1 Answer

Wiring diagram


Hello, If you go to google and look up wiring diagram there is a web site that gives you all of the diagrams.  Hope This helps (Please Take The Time To Rate Me)

Mar 15, 2009 | 2002 Ford Windstar Cargo

2 Answers

Neutral safety switch adjustments


96 Plym. Gr. Voyager (same as Dodge) 4speed A/T can't locate neutral safety switch on drivers side front of trans. My book shows different location/picture (Haynes manual). Any ideas where to get picture/diagram for reference? Initial problem van starts normally but often only clicks when key is cycled through start cycle until it finally starts. Battery good (3 yrs and checked good), replaced ign. switch behind key tumbler assembly(NAPA Echlin part), relay at fuse block in engine area a checks OK with VOM meter, next item is neutral safety switch that also runs backup lights. I've opened area by removing air filter assembly for better view from top or under car but my switches are not in same location as Haynes book shows. Van has towing package and lockup torque convertor if that makes difference. Need source for diagram of trans exterior. Tha nks to all you helpful souls!

Jul 26, 2008 | 1996 Dodge Caravan

Not finding what you are looking for?
1992 Toyota Celica Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...