Question about 1995 Nissan Pickup

Open Question

How to remove cowl grills on 1995 nissan trick

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windshield wiper moter went out i need to change it out. how do i change it?


  1. Disconnect the negative battery cable.
  2. Remove both wiper arm and blade assemblies.
  3. Remove the cowl grille attaching screws and lift the cowl grille slightly.
  4. Disconnect the washer nozzle hose and remove the cowl grille assembly.
  5. Remove the wiper linkage clip from the motor output arm.
  6. Disconnect the wiper motor's wiring connector.
  7. Remove the wiper motor's three attaching screws and remove the motor. To install:
  8. Install the motor and attach the three attaching screws. Tighten to 60-85 inch lbs.
  9. Connect wiper motor's wiring connector.
  10. Install wiper linkage clip to the motor's output arm.
  11. Connect the washer nozzle hose and install the cowl assembly and attaching screws.
  12. Install both wiper arm assemblies.
  13. Connect the negative battery cable.

tecnovative_158.gif

Installing the wiper arm connecting clip.


tecnovative_159.gif

Feb 25, 2011 | 1992 Ford F250

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

Need to remove my wiper assembly on my 1995 plymouth voyager to remove my wiper motor


the cowl grill by the front of the windshield must be removed [6 screws, three in the grill and three along the front edge] to have access to the crank arm. Remove the nut from the crank arm to detach from the wiper motor

Sep 21, 2010 | 1995 Plymouth Voyager

1 Answer

Location of ecu on a 2005 ford freestyle


Keep in mind the definitions:
* ECM = Electronic Control Module (prior 1995 computer, OBD1)
* PCM = Powertrain Control Module (1995 and newer, OBD2)


Ford Freestyle 2005 - Powertrain Control Module The PCM is located in the ine compartment, passenger side, mounted to the cowl. Removal & Installation procedure:
  1. Retrieve the module configuration.
  2. Remove the cowl panel grille.
  3. Disconnect the 3 PCM electrical connectors.
  4. Remove the bolt and the PCM.
To install:
  1. Installation is the reverse of removal.

4f23c78.gif

Hope helps (rememnber rated this).

Jul 14, 2010 | 2005 Ford Freestyle

1 Answer

Need to change the headlights on a 1995 pick up....no clue even how to begin


You need to remove the chromed plastic grille piece to get at the screws that hold the headlamps in place. Open the hood, and there are four (I think) screws holding the top tabs of the grille in place. Just above the bumper, along the bottom of the grill, are a couple more screws. Once this grill piece is removed, you will see the screws holding the headlamp frames in place. (Make sure you don't move the adjustment screws. There is one at the top and one at the side set in a recess -- these aim the lights.) With the screws removed, the frame will come off and the headlamp can be removed and the electrical connector disconnected. Reverse everything to reinstall.

Feb 05, 2010 | 1995 Nissan Pickup

1 Answer

Any tricks for removal of oil pan in a 4.0 litre


There is most likely a cross member in the way of the pan dropping down. Remove the cross member, 4 bolts, and the pan should drop once you have removed all the screws. You will need a seal cutter or a putty knife of some type to break the seal lose as Nissan uses a liquid gasket sealer when the engine is assembled.

Oct 31, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Heater blower


your blower resistor is bad

Apr 21, 2009 | 2001 Dodge Durango

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

1 Answer

The wiper blade connection has released from the wiper blade motor bar that controls the wipers movement. You can hear the motor working but the arms have been disengaged.


please rate as fixya if this is what you need. Mounting Arm and Pivot Shaft —Windshield Wiper Removal
NOTE: The windshield wiper pivot arms (17526) must be in the highest position to remove them.
  1. Turn the ignition switch (11572) to the on position.
  1. Turn the windshield wiper (17500) on.
  1. Stop the windshield wiper pivot arms at the highest position by turning the ignition switch off.
  1. Remove the windshield wiper pivot arm.
    1. Remove the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the windshield wiper pivot arm.

  1. Raise and support the hood (16612).
  1. Remove the cowl grille seal.
NOTE: The two cowl grilles overlap at the center. The LH cowl grille must be removed first.
  1. Remove the LH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the LH cowl grille.
6a042b2.gif
  1. Remove the RH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the RH cowl grille.
bfba69b.gif
  1. Remove the mounting arm and pivot shaft.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the mounting arm and pivot shaft.
8169c1e.gif

Mar 14, 2009 | 2000 Ford Expedition

1 Answer

Windshield wiper bushings


Remove the wiper arms. Remove the metal cowl cover. Remove the [lastic screen/ grill. You will find the bushings on the arms under the cowl cover.

Oct 04, 2008 | 1995 Dodge Dakota

Not finding what you are looking for?
1995 Nissan Pickup Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...