Question about 2007 Pontiac G6 GT Convertible

Open Question

Replace evaporative purge solenoid 2007 Pontiac G6 GTP

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

Ad
  • 2 Answers

SOURCE: Changing blinker on 2007 Pontiac G6

It's a monster pain to get to them, but it's doable. Once you empty the trunk, you'll see 4 black knobs - approx 1.5 inches in diameter. You'll need to remove all of these (they just unscrew, but they are plastic, so be careful not to strip the threading) in order to access the rear light assembly.

They're in there snug, but once you find the appropriate sized socket (I wish I could recall well enough to tell you what size, b/c I remember that it WAS an odd size), you'll have to remove all 3 bolts and then push the whole assembly out from inside the trunk.

Once the assembly is out, you will see the rear of the sockets, which simply push and turn to get the lamps out of. As long as you have everything open, I suggest changing ALL of the lamps (brake, tail, and turn signal) on BOTH sides, since the lamp life for all of these is about the same and it's such a pain to get to them in the first place.



Posted on Apr 13, 2009

tbirdfan1
  • 3051 Answers

SOURCE: How do you replace the battery in a keyless remote

hello there
first you will need to remove the cover usingaflat tip screwdriver
look for a slot on theback of the fob or it may even have a slot inthe middle of the back for it simply pry up on the slot or it may unscrew or pop off
and it will come off
once your battery cover removed. Before you tear the battery that gave you weeks of frustration right out of the thing, take a look at how it's in there so you can put the new battery in correctly. Most remotes have a + sign on the side that gets the + side of the battery facing up, but you'd be mad if yours was the remote that decided not to provide that info.:

Posted on Nov 23, 2009

wracefans24
  • 1985 Answers

SOURCE: need a diagram fo replacing serpentine belt on a

if you buy your belt at auto zone parts,the belt routing is on the package

Posted on Dec 15, 2009

omaromid
  • 332 Answers

SOURCE: How to clean O2 sensor on a 2007 Pontiac G6?

O2 sensor are located before and after Catalytic Converter ( exhaust system of your car). If you car's engine is 4 cyl you have 2 O2 sensors and if you car's engine is 6 cyl then you have 4 O2 sensors ( for each bank, 2 for left bank and 2 for right bank). Hope it helps and comment if you need more advice. Please don't forget to rate the answer it helps with my ratings, thanks!

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't it shift?


08 Pontiac G6 shift solenoid replacement - YouTube

? 2:31
www.youtube.com/watch?v=9Lq5Va2Xie0
Dec 26, 2012 - Uploaded by 1711juanito Showing how to replace a shift solenoid on a 2008 Pontiac G6with 80000 miles! Comment with any questions.

Oct 28, 2015 | 2007 Pontiac G6

2 Answers

Where is My purge canister located on my 2008 G6


Canister or the solenoid to run it?

Apr 06, 2015 | 2008 Pontiac G6

1 Answer

2007 pontiac g6 transmission filter replacement


Remove the transmission pan - some don't have drain plugs, have a big pan underneath to catch the fluid. Pull filter and install filter on. Clean any debris from pan. Install gasket onto pan and install pan back onto transmission. Torque bolts to factory specs. Fill with approved ATF.

Hope this is helpful :-)

-Scott
25449121-csuuapdgb0syz0ddt50mju2i-5-0.jpg
Pontiac G6 GT Trans Fluid and Filter Change time lapse GoPro

Feb 19, 2015 | 2007 Pontiac G6 GTP

1 Answer

Purge solenoid location 2008 torent


Evaporative Emission Canister Purge Solenoid Valve Replacement
Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Disconnect the engine wiring harness electrical connector (4) from the evaporative emission (EVAP) purge solenoid.
Remove the oil fill cap. Lift upward and remove cover from ball studs.
The purge solenoid is under the plastic cover on top of the engine .
Disconnect the EVAP pipe quick connect fitting (1) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the EVAP pipe quick connect fitting (2) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service. Remove the EVAP purge solenoid bracket bolt (3). Remove the EVAP purge solenoid.

the purge

Sep 20, 2014 | 2008 Pontiac Torrent

1 Answer

Where are the camshaft actuator valves located on a 2006 Pontiac G6 GTP 3.9L V6


I believe you are thinking of the wrong kind of valve. You do not have solenoid valves, you have mechanical valves that open and close off of the lobes of the camshaft.

Aug 23, 2014 | 2006 Pontiac G6 GTP

1 Answer

How to change purge value solenoid for a 2006 potiac v6 gtp


find its location on the engine... there will usually be an evap guide picture under the hood somewhere... when you find the solenoid, simply disconnect the electrical and one hose and pull the valve off the engine

Apr 27, 2014 | 2006 Pontiac G6

1 Answer

2009 pontiac g6 purge valve solenoid


code PO171 fuel trim system lean bank 1 conditions.possible causes air leaks in intake manifold exhaust pipes or exhaust manifold. fuel control sensor is out of calibration such as ECT IAT MAF.fuel component faulty like stopped up fuel filter fuel injectors clogged low fuel pressure faulty fuel pump. HO2S element contaminated or has failed. purge solenoid is part of EVAP system. if you have faulty purge solenoid you would get code like PO443 meaning evaporative emission control system purge control valve circuit malfunction.try replacing fuel filter clean fuel injectors see what happens.

Apr 04, 2013 | 2009 Pontiac G6

1 Answer

2005 Pontiac G6, Check Gas Cap alert on console. checked cap and cover and it still persists. any ideas ???


This sensor will also set when there is a leak in the evap system. Check the hoses under the car as they go into the fuel tank. One of them is for the evaporation system. It goes to the evaporation cannister. If that hose is leaking, or if the purge valve is stuck open, you can also get the message you are getting. Your evap cannister and purge valve should be right by the fuel tank, but you'll need to also trace the hose from the cannister to the engine to make sure that hose isn't leaking. If you have any questions, please let me know.

Oct 18, 2010 | 2006 Pontiac G6

1 Answer

Does my 07 pontiac g6 gtp breaklights run off a fuse


yes they run off of a fuse in the main fuse box, if it is not labeled check your owners manual for the fuse location.

Dec 08, 2009 | 2007 Pontiac Grand Prix GXP Sedan

Not finding what you are looking for?
2007 Pontiac G6 GT Convertible Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...