Question about 1998 Isuzu Trooper

Open Question

1988 isuzu trooper 2.6 how to change the cam belt

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: alternator belt diagram 1992 Isuzu trooper

1. Remove battery terminals and secure them away from the battery posts using nylon wire ties.

1a. Fine some comfortable eye glasses (clear or yellow) and keep them on. There are plenty of opportunities to get debris in your eyes during this procedure.

2. Spray "PB Blaster" (loosens bolts) on two bolts that secures alternator.

3. Jack-up vehicle on side to access alternator. Use a jackstand to support.

4. Using a 10mm open-ended wrench, loosen the bolt that swings the alternator. Screwing the bolt "in" or toward the engine will allow play to increase in the alternator belt. Loosen the 12mm bolt slightly next to the 10mm bolt (approximately 1.5" toward engine).

5. Continue to loosen 10mm bolt until there is enough slack in the belt to remove the belt from the alternator pulley.

6. Remove belt. It may be possible to remove belt without removing fan faring. Maybe not. If not, you will need to remove plastic fairing. If you must remove fair, go below fan fairing and disassemble connectors that hold together pieces of fan fairing. Carefully remove.

7. Install alternator fan from above.

8. Check that alternator belt is on all tracks (from below with a flashlight), and slowly tighten.

9. Secure 10mm and 12mm bolts. Recheck tightness.

10. Reassemble battery connection and run vehicle at idle for about 5 minutes. Check belt for proper tension.

11. CAREFULLY check tension of belt. Or disassemble battery connections and re-check belt tension.

12. Reassemble fan fairing (if not already assembled), re-connect battery terminals, and have a nice day. :-)

Posted on Jan 04, 2009

Ad
  • 2 Answers

SOURCE: fuel filter change out in 2002 isuzu trooper

easy under the driver side need fuel tool from auto store. 30 min or srew driver push the clips in and pull. carefull lots of gas...

Posted on Jan 09, 2009

  • 15 Answers

SOURCE: we want to change the serpentine belt on 01 isuzu trooper

0b71af3.gif
# 3...there is the tensioner.

Posted on May 06, 2009

germcelchar
  • 389 Answers

SOURCE: change a cv boot on a 1996 isuzu trooper

First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Posted on Sep 28, 2009

stevenhurc
  • 450 Answers

SOURCE: how do i reset my timing beltwarning light after

this is not right there should be a rubber grommet in cluster lens take out and press button with ignition on to reset light just like resetting trip meter

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 trooper starts runs fine till warms up shut off starts back acts like its not get gas


which engine?
we can NOT GUESS engines, ever.
get a tuneup this decade?
that be first. (spark part filters if engine is gas engine)

1988, very few of those on the road
we have one parked in a field here.
carb dead, no parts to fix it. no willing persons to fix it.
1988 had (usa) a 2.2L Diesel
and a gas 2.6L I4
the 2.6L needs a new cam belt at 60k miles
ignoring that?
and all those old spark parts, and filters.
most cars this old are zero service.
and fail to run.

new cap /rotor,wireset, spark plugs,filters and and cam belt.
and it might run,. now.
do the book published 60k service points, if ignored.

there are 50 other causes of stalling besides
neglect.

Mar 07, 2017 | 1988 Isuzu Trooper 2 Door

1 Answer

I have isuzu trooper 1988 am changing the timing belt but i forget mark the timing and now i cant get it start.


Take it to a trained mechanic that works on isuzu's. If you have never put a belt on one of these do not attempt it.The cam pulley turns aver three times to one rotation of the camshafts, no marks.

Oct 23, 2010 | 1988 Isuzu Trooper 2 Door

1 Answer

Cam belt timing 1994 Isuzu trooper big horn


no timing, cam belt must be installed corectly inorder to have right timing.

Oct 03, 2009 | 1994 Isuzu Trooper

2 Answers

Same problem 1988 trooper clutch issues


Have seen em put on with the bleed screw at the bottom by mistake ?

Jul 31, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

What is the pressure required for 1988 isuzu trooper fuel injection?


If you have the belt driven injector pump its 2560psi on the first spring and 3903psi on the second spring.
If the pump is gear driven and single spring injectors its 2631psi

Jul 05, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

1988 Isuzu trooper 2.6l


yes, i had the same problem. i've got a 93 isuzu trooper, but look in the chilton's manual, the engine and fuel systems are all for the most part identicle. My fuel pump went out, so I had to put it on a lift and drop the fuel tank. the pump is actually Inside the fuel tank. swapped it out along with the strainer, and now it runs like a dream. hope that helps.

Jan 08, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

Isuzu trooper


it is a cam belt usually known only as timing belt dealer or any auto zone or advance auto parts should carry one

Oct 16, 2008 | 1993 Isuzu Trooper

1 Answer

1999 isuzu trooper 3.5 broken timing belt while driving on freeway


these free wheel when belt breaks they dont bend valves
but you need to remove both rocker covers to align cam gear mark and have cam lobes in these positions
cb47a33.jpg

Jun 16, 2008 | 1999 Isuzu Trooper

Not finding what you are looking for?
1998 Isuzu Trooper Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...