Question about 2005 Nissan 350Z

1 Answer

I just put in a set of headlights on my 05 350z. They are they Spyder smoke and are plug and play. Hooked up HID and they worked fine, for a few minutes. Passenger side still works fine on low beam but drivers side low beam does not. All lights work fine except for the drivers low beam. All bulbs and fusses and ballasts are good. Any suggestions. Two days trying to figure this out

Posted by on

  • Shade Tree All Repair

    Did you touch the bulb with your bare skin your finger tips if so it is probably blown, this happens alot but if this is not the problem check your light relays under the hood then all fuses but check the bulb first for continuity please thanks.

  • Shade Tree All Repair

    remember relays are not fuses and are not ballasts there are 2

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

For starters, "..worked fine, for a few minutes." sounds like a current overload issue. Is the headlight wattage greater than the wattage of the bulb(s) you are replacing? If so, you're asking for trouble; the least being burnt wires and circuits. Worst case would be a fire.
Assuming you're within wattage specs and assuming you've checked fuses, it's a matter of using a test light working backwards from the headlight ( if you have power to the headlight but light does not work, you either have a bad bulb or it is not getting "grounded").

Posted on Feb 16, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7353 Answers

SOURCE: my passenger side low beam headlight is out. the

Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Posted on Dec 16, 2009

carlsbiz
  • 1124 Answers

SOURCE: low beam does not work on passenger side only

It could be a realy..
Find the relay location in your manual..

Have a great day !

Posted on Sep 19, 2009

  • 7353 Answers

SOURCE: Passenger low bean headlight doesn't work. The

You will need to provide what year car, engine size, ect so a diagram can be found to help you.

Posted on Dec 16, 2009

  • 1 Answer

SOURCE: Audi A4 2002 Low beams & Right front turn signal stopped working

but on 2002 A4, F20 and F21 are empty! Does anyone has an idea where the headlight fuses located?

Posted on Jun 10, 2010

alicantecoli
  • 22246 Answers

SOURCE: The passenger side low beam headlight is not working, replaced with new light bulb but it still doesn't work

check the fuses as it has a fuse for each headlight if iam not mistaken

Posted on May 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace front HID light bulb? and where can I purchase parts for replacing?




  1. INSTALLATION GUIDE:


  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights


  3. Parts Identification:


  4. Projector Headlight


  5. Halo & L.E.D.


  6. Bottom of the Headlight:


  7. Ballast Bracket, Halo Wires(red/black)


  8. Turn Signal Adaptor


  9. TOOLS REQUIRE


  10. 10mm - 8mm socket


  11. Philip Screwdriver


  12. Crimper/Pliers


  13. For more information about how to install your vehicle, come visit our youtube page on


  14. http://www.youtube.com/spyderauto


  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.


  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.


  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.


  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.


  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.


  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.


  21. STEP:


  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.


  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.


  24. Factory Xenon Headlight


  25. Spyder Projector Headlight using Factory Xenon Lights






replace-front-hid-light-bulb-purchase-afy5cnsznmokzumyhdcbeseq-5-0.jpg

May 21, 2014 | BMW 335i Cars & Trucks

2 Answers

I have problem with hid light


follow this link to u-tube video not the exact vehicle but the principle will be the same,or search for your exact vehicle
How to replace low beam xenon HID bulbs 2006 BMW 330i

May 08, 2014 | 2007 BMW 335i Coupe

2 Answers

How to change headlight bulb


On the back of the headlight where the wires enter, you should be able to twist and remove the lamp holder. Be careful with the new bulb if it is halogen, do not touch the bulb!!

Apr 13, 2013 | 2000 Hyundai Sonata

3 Answers

Replace headlight bulb


  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
  27. PLS VOTE ME
BMW e46 HID Headlight Replace
replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-0.jpg

replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 23, 2012 | 2000 GMC Denali

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

2 Answers

Lt. headlight low beam wont work after replacing the bulb.


I assume it didn't work before you changed the bulb either. You'll have to check for voltage at the bulb socket when the low beam headlights are turned on. If there is none you'll have to trace the wire back to where it splits from the right low beam headlight. If there is voltage there you have a problem with the new bulb.

Apr 10, 2011 | 1991 Lexus LS 400

1 Answer

I installed a High beam hid kit and read online that they needed a resistor in that year to trick the computer. after installing the kit and the resistors to the high beams pos and neg it still flashes...


I don't know why you would install resistors inline for an HID kit, they should be 'plug and play'-you plug the connector for your halogen lights into the ballast input for the HID kit, then plug in the HID bulb harness/ bulb to the ballast output, install the bulb into the housing-done. Some people have installed relays to the lights because when the HID's 'light off' the use a lot of power until the bulbs warm up, then they actually consume less than a halogen bulb (usually 35 watts HID to 55 or more halogen). I have HID's in a number of cars and don't have relays hooked up on any, just 'plug and play' and I have no issues whatsoever.

Apr 03, 2011 | Dodge Ram Pickup 1500 Cars & Trucks

3 Answers

I have a 2004 Nissan Maxima with hid headlights an the bulb is blown an i have replaced the bulb an it still doesn't work, i checked the fuse box inside an outside, is their any other fuses i can...


It sounds like you have wire problem. This problem can be manny problems from a short due to exposed wire or it is broken somewhere... ect. if it is not the wire check further back the line to see if the buse is recieving power. Or it could be as simple as the plug you put the bulb in has a broken contact tip

Mar 29, 2011 | 2005 Nissan Maxima

2 Answers

How do you change front headlight blub 2008 sonata


how do you change front headlight blub 2008 sonata

Nov 28, 2009 | 2008 Hyundai Sonata

2 Answers

How to install hid on a bmw 325xi 2006


INSTALLATION GUIDE:
BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
Parts Identification:
Projector Headlight
Halo & L.E.D.
Bottom of the Headlight:
Ballast Bracket, Halo Wires(red/black)
Turn Signal Adaptor
TOOLS REQUIRE
10mm - 8mm socket
Philip Screwdriver
Crimper/Pliers
For more information about how to install your vehicle, come visit our youtube page on
http://www.youtube.com/spyderauto
Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
STEP:
Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
Factory Xenon Headlight
Spyder Projector Headlight using Factory Xenon Lights
STEP:
pls vote an diam giving you link also for better help BMW e46 HID Headlight Replace
install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-0.jpg

install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Oct 15, 2009 | 2003 BMW 325

Not finding what you are looking for?
2005 Nissan 350Z Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...