Question about GMC Sierra 1500

Open Question

Shut off while driving gas needle won't move - Sierra 1500 GMC Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My 1996 camaro won't move when I step on the gas


Check your linkage if ok ....... you have trans issues most likely torque converter ? ?. Mike J

Jan 11, 2013 | Cars & Trucks

1 Answer

2004 chevy trailblazer LS EXT. My gas gauge is not reading the gas amount and it keeps moving. Gas level can be at half and as I drive it drops but when I stop it moves back to half. Fill it up to where it...


This sounds like the fuel level sensor in the gas tank is going bad, or there is a bad ground at the tank. A technician using a scan tool can monitor the actual fuel level data to verify.
Another possibility is a bad stepper motor in the instrument panel, each gauge had a stepper motor to drive the needle.

Jul 14, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Just bought a '92 plymouth Acclaim with 37000 miles. It's in great shape but I'm not sure if the fuel guage is working. Only drove it home, less than 10 miles. Is the guage mechanical or...


There's a float inside the tank that the fuel gauge works off of. If you step on the brakes or accelerate hard it causes the gas inside the tank to slosh around and you can see the fuel gauge move when you do this. If you know the vehicle has gas in it, the best way to check if the gauge is bad is to drive around enough to where you should have burnt a noticeable amount of gas. If the gauge doesn't move, then there's something wrong with it.


Since the gauge moved when you braked hard, I would assume it's working properly because it picked up on the level change inside the tank where the float's at.

May 19, 2011 | 1992 Plymouth Acclaim

1 Answer

Gas is dumping out of my carb from all seams 1986 w100 dodge 318


If you have gas coming out of the top of the carburetor then you could have either a bad float, a stuck float or a bad needle and seat, all of which are inside the carburetor. The float rises with the level of fuel and shuts off the incoming fuel by pushing the needle valve against the seat thus stopping any more fuel from entering the carburetor until the fuel level drops slightly at which time the needle moves slightly away from the seat and allows more fuel to enter again. You could also have a piece of crud that has gotten between the needle and seat which will prevent the valve from fully closing but that's pretty rare. You will probably need to have the carburetor cleaned, inspected, and have a repair kit installed to fix the problem.

Jun 08, 2010 | 1986 Dodge Pickup 4WD

2 Answers

2001 chevy silverado 4.8 gas gauge not working properly


Fairly common problem with GM vehicles. The sending unit in your tank has a small circuit board that an arm is attached to which moves up and down according to your fuel level. This circuit board and arm are not making good contact. Unfortunately the only good solution is to replace this part.

Oct 28, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Gas Gauge won't move


Replace the fuel sensor / sending unit, it is inside the gas tank, it is a lot of work to drop the gas tank, I have done it on other cars... If you want to do it make sure the tank is almost empty it is very heavy with all that gas inside make sure there is no open flames or cigarretes close
Good Luck

Mar 20, 2009 | 2002 Jeep Liberty

1 Answer

Gas light in 99 beetle won't turn off


it's probably a sensor issue.  

Feb 18, 2009 | 1999 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...