Question about 2007 Jeep Compass Limited

Open Question

Code p000a cam 1/1 slow response

Code p000a

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Dodge Caliber 2.0 DOHC no start, P000a, P000b. Low oil on dip stick.


codes p000A refers to camshaft position sensor(CMP) actuator, intake /left/front bank 1---slow response===causes ---wiring---CMP actuator---ECM

code P000B refers to CMP actuator, exhaust/right/rear bank 1--slow response -====causes ---wiring---CMP actuator---ECM
did it occur to you that if there is insufficient oil in the motor that items that require oil pressure may throw codes when that oil pressure is fluctuating from air being pumped
first fill the sump to the high mark on the dip stick and keep it there , then it the codes reappear have an accredited service centre change the actuators

Jan 13, 2017 | 2007 Dodge Caliber

1 Answer

Trouble code p000a on 06 vw passat. can i drive with this code or will it cause more damage to the car


Cam shaft positioner malfunction. You can drive it. Just have bad gas mileage. Probably run rough to. If it starts making a bunch of chattering noise, time to have it fixed. I wouldn't take it on any long trips either.

Aug 07, 2016 | Cars & Trucks

2 Answers

My 2004 Honda CRV showing code P0133 and P0171


  • P0133 O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)
  • P0171 System Too Lean (Bank 1)
Hi Michael, After fixing errors you need to reset your computer by disconnecting the battery for a minute or two, Also you'll need your radio code to reset your radio, I hope this helped...........CHEERS..

May 07, 2016 | Honda Cars & Trucks

1 Answer

Code p000b


code p 000B refers to camshaft position (CMP) actuator , exhaust/right rear bank 1---slow response===causes --wiring---CMP actuator--- ECM
The actuator is what allows hydraulic pressure through to the sprocket assembly to change the valve timing, in this case to the exhaust cam shaft on the right rear bank 1
If you do not have expertise in this repair , I would suggest that you find an accredited service shop with experience in your make of vehicle

Oct 02, 2015 | Cars & Trucks

1 Answer

I have a P000a code, camshaft position slow bank 1. Is this a hard fix?


The sensor itself is not hard to replace but the issue is more likely a streched timing belt. Most po340 and poooa codes are caused by timing problems.

May 07, 2015 | 2005 Audi A4

1 Answer

What does code p2004 mean?


P2204-The PCM detects that the position feedback of the Manifold Flow Valve Position Sensor is not within range of the adapted value learned during in-plant initialization or after a non volatile memory reset (adaptive memory clear).
Usually means the air flow valves are stuck open or closed. You have to remove the intake and either free up the valves by cleaning them and lubing them, or replace the intake with a new one with new valve.
P000A &P000B:
The codes are for Cam position sensor A and B slow response.

Ever changed the timing belt on that car? It may have jumped a tooth. Check your maintenance schedule for lifespan. I believe it is 65,000 mile interval on changing it.
Note - some engines will be badly damaged if a timing belt snaps or skips too far, as the pistons and valves occupy some of the same space at different times during the engine operating cycle.
The car may also have a faulty timing belt tensioner, which should also be replaced with the timing belt.
Another possible cause is a faulty sensor in the distributor.

Jul 21, 2014 | Chrysler Sebring Cars & Trucks

1 Answer

Error code troubleshooting


It's your AVCS/cam shaft issue, bring the dealership since this issue is on Subaru TSB. Possible they replace the ECU/ECM unit.

02-132-12R Technical Service Bulletin Diagnosis and Repair for AVCS-Related DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021 and P0024

Jul 21, 2014 | 2012 Subaru Impreza 2.0i 4dr Hatchback...

1 Answer

2007 dodge caliber p000a pooob


these codes are slow response from CAM sensor , can becaused by poor condition oil , when was last oil change? if not recent say 6000 miles change the oil and filter , wipe codes and road teast and re-read codes , if re-appears then cam sensor could be at fault,or the sensor solenoid , what grade oil do you use ? 5w 20 is the correct grade let me know how you get on if you wish

May 19, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Jeep compass check engine code p000a


I had my alternator replace in 07 jeep patriot and the tech broke my pcv hose. I drove a mile down the road and my check engine light came on. I went to auto zone and got code p000A i just would like to know what the pcv hose be the problem?

Aug 07, 2013 | Jeep Patriot Cars & Trucks

2 Answers

2007 Jeep Compass Code P000A and P000B problem what is it?


P000A is either wiring fault, a fault with the ECU/PCM or a mechanical fault the camshaft.

P000B is slow response from the cam sensor. It can be cause from dirty oil or the wrong type of oil.

In both cases, if your sure the oil is correct then there is an issue with the cam sensor or cam sensor solenoid.

I hope this helps; remember to rating this and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment.

Have a nice day and thanks for using FixYa.
Jose.

Oct 17, 2011 | 2007 Jeep Compass Limited

Not finding what you are looking for?
2007 Jeep Compass Limited Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...