Question about 1998 Chevrolet Blazer

1 Answer

The radio is on but there is no volume

I have looked a tall the fuzzes and have replaced the bad ones, but I turn the radio on and I shows its on but there is nothing...no volume...needing help!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 129 Answers

Speakers hooked up and are they good.

Posted on Jan 24, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The radio plays full volume on right channel when turned on.


Anything I tell you is going to be a guess, since there has been no testing done, and we don't have the model number of the specific radio involved. However...
For a 20 year old radio, the volume and balance is almost certainly controlled by a potentiometer that has input into one leg of the fixed resistance, and the other leg (of the fixed resistance) is grounded. The movable center tap is the output to the amplifier - and its position controls the volume to that channel. If the ground leg becomes disconnected (broken wire, or a cold solder joint, or even a break in the resistor within the body of the potentiometer) then instead of "dividing" the volume, it simply provides a slight resistance inline - short answer: It goes full volume.
You can try running the control full range back and forth, and even just the old time "slap it" approach, to see if you get any static or change. If you do, that pretty well confirms the diagnosis. [If not, it just means the break is not close to touching - still almost certainly the right answer though.]
Only fix is going to be disassembly. You then may be able to find the break (and resolder it), and/or replace the volume potentiometer. Note that if you have remote volume/balance control (controls on the steering wheel), then there is some extra wiring that can likewise be involved. jk

Feb 27, 2015 | 1995 Jeep Grand Cherokee

1 Answer

The dial on radio volume not working


sounds like the radio volume is bad, and no volume from radio Time for a new radio. Good-Day!

May 17, 2014 | 2011 Hyundai Elantra

1 Answer

Volume will not work


front cover on radio is bad, replace

Apr 15, 2013 | 2003 Pontiac Grand Am

1 Answer

Car speakers fuzz


Do not use factory speakers with a aftermarket radio the ohm rating will not match and you will never get any kind of good volume out of them.
New aftermarket stereo's are set for 4 ohm load. consult ohms law when purchasing new speakers. ALWAYS run new speaker wire to your speakers. If problem still persists then you have to install a choke (noise suppressor) on the positive side wire of you stereo or relocate it to another source of power.
Resistor spark plugs never hurt as well.

Oct 24, 2012 | Toyota Cars & Trucks

1 Answer

Radio on but no sound after installing after market subs


to create a spark you must have had power connected somewhere. Did you have your radio turned on when you connected? if yes you may have blown the amp in the radio. If no then you have other issues with wiring and possible damage.
It's one of those instances where I'd need to be there to diagnose it.
Start by double checking the stereo is working, check its wiring is correct try each speaker connection in turn. If the stereo works and all the outputs work then double check the amps wiring and try a normal speaker connected to it. You must get the picture by now, you need to identify the source of the fault. to help you better I'd need a wiring diagram.

Dec 20, 2011 | 2003 Toyota Camry

1 Answer

Radio says A/V off. no volume on radio or cd - how do I turn AV back on or get volume


My range rover consol shows a/v off, how do I get it back to a/v on, thank you.

Dec 13, 2011 | 2005 Land Rover Range Rover

1 Answer

My Volkswagen radio On my Jetta 2004. Shows a error 3 on Cd After I have taken the Cd Out. Theres no sounds for the radio anymore. The Radio turns on but theres no volume?


Is speakers blown? How about any fuses? Or try and trace down any of the wiring. Could be one unplugged, or gone bad, like shorting out maybe.
Good luck to you.

Feb 03, 2010 | 2003 Volkswagen New Beetle Convertible

1 Answer

My radio light comes on but no sound


Check all fuses for the radio. One could be bad.

Dec 24, 2008 | 2003 Hummer H2

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...