Question about 1996 GMC Yukon

Open Question

95 gmc jimmy 4.3 v6 no four wheel drive. push button on dash it show s that it should b in wrong does not engage

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: 1996 JIMMY / 4 WHEEL DR DOESN'T ENGAGE but LIGHT TURNS ON

The problem is in the transfer case. My mechanic said there is a pin that engages the 4x4. My pin sheared off. He replaced it. It works fine now.

Posted on Feb 03, 2009

aandwmore
  • 13 Answers

SOURCE: 97 JIMMY,PUSH 4X4 BUTTON,NOTHING HAPPENS

I had the same problem with my 99 Jimmy. try to disconnect your battery for about 5 minutes and see what happen. it fixed mine by doing it.

Posted on Feb 07, 2009

  • 6 Answers

SOURCE: Front drive, 4 Wheel drive won't engage

Check the switch on the transfercase remove the vacume lines if there is oil in them the switch has to be replaced and the lines should be cleaned out you should also check under the battery tray to make sure the boot is not ripped that controls the leaver to engage the front axel

Posted on Feb 16, 2009

mattman2112
  • 57 Answers

SOURCE: 4x4 in working

try reversing six to eight feet after shifting into 4WD. PLEASE RATE MY ANSWER.

Posted on Feb 26, 2009

poolgod27ia
  • 1 Answer

SOURCE: 4x4 will not engage in 96 gmc yukon

I just fixed a friend of mines 96 yukon...shift to neutral press 4H and u can hear the actuator make noise (we even replaced it with a new one his idea and the same thing happen as old one), so as he hit the switch for 4H i layed under it (on 4 jack stands) and I could hear the motor on the transfer case make a loud noise (well thats working) and before all this I asked him did u check all your fuses (he said guarnteed to be all good) one night it was bothering me so i looked through the owner manual for the yukon and in the fuse box on driver side by the door there are (2) fuse for the 4wheel drive unit,pull one of the fuses good...pulled the other one and it was blown put in a new fuse and it works like brand new..pull fuse for anything that has to do with 4 wheel drive componants,

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 jimmy push button 4x4 wont engage


Could be the servo on the front diff not activating. Could be a power prob or failed unit.

Jan 15, 2013 | 1994 GMC Jimmy

1 Answer

How to get a push button four wheel 96 jimmy out of four wheel drive


take the switches 2wd 4wd hi 4wd lo out of the dash and unplug them all then use small wire to jump the 2wd connectors then replace new 4wd button and new 2wd button

Mar 16, 2011 | GMC Jimmy Cars & Trucks

1 Answer

Four wheel drive stuck in neutral. Won't go into 2high or back to 4 wheel drive. Transfer case was replaced. Its a 2000 Jimmy.


If you have the push buttons on the dash board you must follow the instructions in your owners manual to return the transfer case to 2wd from neutral. I don't remember for sure but I think you must have the transmission in neutral, foot on brake, press and hold both 2wd and 4wdlow buttons at same time. My father who lives 45 miles from me has the Jimmy, I don't. Hope this helps, Jim

Jan 04, 2011 | 2000 GMC Jimmy

1 Answer

1996 gmc jimmy started making noise sounding like it is is right front was told need to replace wheel hub which was done. Still making the same noise in 2 wheel drive. when you push button for 4 wheel...


Sounds like your front axle is trying to engage but does not engage fully.check your vacuum going to the t-case switch and then if that is ok check your vacuum at the front axle actuator.It is located under the battery tray.

Dec 06, 2010 | 1996 GMC Jimmy

1 Answer

I have a 1996 gmc jimmy that has a push button 4 wheel drive but my four wheel drive isnt working


it may be unplugged from button pull the case out of dash to be sure ther is a connection @ plugged in good, the little panel pulls out W/buttons @ all

Aug 12, 2010 | 1996 GMC Jimmy

1 Answer

Push button 4 wheel drive stuck in 4 wheel hi


My GMC Jimmy '01 would slip from 2-wheel to 4-wheel drive while I was driving. First time it happened my mechanic replaced a small part. This last time, he couldn't find anything wrong so he popped the 2-4 out and disconnected the 4-wheel drive. Now I don't have the problem.

Feb 22, 2010 | 2001 GMC Jimmy

2 Answers

The 4-wheel drive on our 2001 GMC Jimmy does not seem to engage. It is new to us and came with no manuals. Are we doing something wrong or is it just not working?


First and foremost can you tell me if the lights are showing up on the 4x4 selector switch ? Second if they are illuminated ( should be in 2-Hi ) when you select to go into 4-Hi or 4-Low does the selection flash? And Lastly can you hear a sound of any type (clicking, ticking, thumping) when you push the button?

Jan 01, 2010 | 2001 GMC Jimmy

1 Answer

4 wheel drive will not engage 4 wheel drive button is pushed


bad trasfer case selector motor common problem i ve a ton of these replace that motor and youll have 4 wd again ,the part is costly about $ 300.00. hope this helps.

Dec 13, 2009 | 1999 GMC Jimmy

1 Answer

1999 Jimmy 4wd not engaging. It has push button


could be your front actuator or your actuator motor on the transfer case.

Apr 12, 2009 | 1999 GMC Jimmy

2 Answers

Front drive, 4 Wheel drive won't engage


that vacume line goes back to the transfer case, the end that goes behind the motor hooks to a steel tube so it does not get hot from the exhaust., my guess it should be hooked up so it will feed vacume to the vacume ball so it can lock in the axels. if you start the car and shift into 4 wheel drive and listen under hood you should hear a hissing sound, that is vacume, if you can't hear it there, you may have to craw under the right side to hear it, probably came unhooked underneith the car

Feb 01, 2009 | 1995 GMC Jimmy

Not finding what you are looking for?
1996 GMC Yukon Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...