Question about 2005 Pontiac Sunfire

Open Question

No warning buzzer for lights left on

No warning buzzer for the lights left on or keys in ignition

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuse for the ignition key reminder for a 1999 Suzuki esteem


thats cute, ask use to do easter egg hunt,
with no symptoms stated.
sure all circuits are fused. (cept starter motor)
but most fuses run from 2 to 30 (loads) other things,(30 is park)
so. what is your point or question , why not post a real question?
like a symptoms or what you are about to do. or?
see, put us on same page, for big time better help.

RTM (read the manual yet)
https://suzukipitstopplus.com/Products/10133-1999-esteem-service-manual.aspx

$4
is the buzzer dead.at all times?
is the buzzer dead for all warnings? or just the key left inside ign.

Mar 17, 2015 | Suzuki Cars & Trucks

1 Answer

My 2005 Toyota corolla s has started this beeping from the left side of the dash when I turn the ignition on. Has no warning lights and runs great! Just wondering what's going on and how to fix this?...


has it got a handbreak warnng buzzer or a door open buzzer might be shorting or some time its the clickers for the indicators buzzing is it there when the cars ignition is on or only when it runs could be the petrol pump depending where it is hope these help

Aug 18, 2012 | Cars & Trucks

1 Answer

Is there a buzzer for the lights on 2003 jetta?


depends on market....key in ignition open door, buzzer....key out of ignition lights on,buzzer.BUT.....pull dipswitch toward you (flasher)with key out NO BUZZER. VW pull out anything that costs to make a car cheaper for any given market.even a cigarette lighter is missing on some cars.......no ashtray in others.....

Jul 11, 2010 | 2003 Volkswagen Jetta TDI

1 Answer

I have a 97 gmc jimmy 4wd. received dtc s 740 , 785 ,1860. just recently received 101. I rectified 101 code by replacing air filter and cleaning MAF sensor. I have traced the remaining codes to the...


Have no clue as to what you want ? Like to try an explain a little better . What do DTC'S 740 , 785 and 1860 have to do with key in ignition chimes . Plus i'am assuming the DTC'S you have listed all start with P - P0740 , P0785 and P1860 .
DTC P0740 TCC Enable Solenoid Circuit Electrical (2.2L)
DTC P0740 TCC Enable Solenoid Circuit Electrical (4.3L)
DTC P0785 3-2 Shift Solenoid Circuit Electrical (2.2L)
DTC P0785 3-2 Shift Solenoid Circuit Electrical (4.3L)
DTC P1860 TCC PWM Solenoid Circuit Electrical (2.2L)
DTC P1860 TCC PWM Solenoid Circuit Electrical (4.3L)

None of these have anything to do with warning chimes .

Key-In Warning Buzzer
Voltage is supplied at all times to the truck BCM through the following components:
• The underhood bussed electrical center (UBEC) fuse 4
• CKT 1140 (ORN)
The chime or buzzer sounds if the following conditions exist:
• The key is in the ignition switch
• The vehicle is not running.
• The left door is open.
When the door is open, the LF door jamb switch closes to ground. This provides a ground to the truck BCM through the following components:
• CKT 126 (TAN)
• The left front side door jamb switch
• CKT 1050 (BLK)
• SP203
• C203, cavity F12
• G203
The chime or the buzzer will sound for as long as the door is open and the key is in the ignition switch.


Turn the ignition switch to the OFF position.
Remove the key from the ignition.
Using the scan tool, enter BCM Data List.
Select Input 1.
Does the KEY IN IGNITION test display NO?
3
Turn the ignition switch to the OFF position.
Remove the key from the ignition.
Using the scan tool, enter BCM Data List.
Select Input 1.
Does the KEY IN IGNITION test display NO?
--
Go to Step 4
Go to Step 8
4
Turn the ignition switch to the OFF position.
Remove the key from the ignition.
Move the headlamp switch to the OFF position.
Using the scan tool, enter BCM Data List.
Select Input 2.
Does the PARKLAMPS test display OFF?
--
Go to Step 5
Go to Step 9
5
Inspect the connections at the BCM.
Are the connections in need of repair?
--
Go to Step 6
Go to Step 7
6
Repair the connections as necessary.
Is the repair complete?
--
Go to Diagnostic System Check - Audible Warnings
--
7
Replace the BCM. Refer to Body Control Module Replacement in Body Control System.
Is the repair complete?
--
Go to Diagnostic System Check - Audible Warnings
--
8
Locate and repair the short to ground in CKT 80 between the BCM connector C2 terminal B9 and the key in ignition alarm switch.
Is the repair complete?
--
Go to Diagnostic System Check - Audible Warnings
--
9
Are the park lamps ON with the switch OFF?
--
Go to Exterior Lights System Check in Lighting Systems
Go to Step 5
Your best bet take to a qualified repair shop

Jul 23, 2017 | 1997 GMC Jimmy

1 Answer

Light warning buzzer constantly on


Have you checked that the headlight switch is in the right position? Are the headlights or parking lights still on when the key is removed?

If so, then rotate the lamp switch to the correct position and the buzzer will go off. Headlights and parking lights are not controlled through the key circuits.

Jan 29, 2009 | Hyundai Motor 1999 Elantra

1 Answer

2006 Sierra-no warning chime


There is not a Fuse for this. Look at the Panel under the Dash on the Drivers Side. At the top there are 2 Boxes or Cicles. The one on the Left should be the Buzzer Relay Box.

Jan 20, 2009 | 2006 GMC Sierra

1 Answer

No warning buzzer that my lights are on


the 1999 elantra was not equipped with a warning buzzer for the headlights, if you leave them on.
the headlights will turn off if you shut the car off, but the parking and tail lamps will remain on

Jan 13, 2009 | Hyundai Motor 1999 Elantra

1 Answer

1990 Jeep Cherokee Ignition key replacement


Removal & Installation
Without Air Bag
See Figures 1, 2, 3 and 4
  1. Remove the turn signal switch.
  2. Insert the key in the lock cylinder and turn it to the ON position.
0900c152800a9f7f.jpgFig. 1: Using a pair of needle nose pliers, remove the key warning buzzer switch and contacts from the steering column
  1. Remove the key warning buzzer switch and contacts AS AN ASSEMBLY using needle-nosed pliers, or a paper clip with a 90° bend.
0900c152800a9f80.jpgFig. 2: Lock cylinder retaining screwSome steering columns may have a retaining screw holding the lock cylinder in the column. When servicing this type, simply remove the retaining screw and remove the lock cylinder.
0900c152800a9f81.jpgFig. 3: Using a small thin bladed tool, press in the ignition lock clinder retaining tab ... 0900c152800a9f82.jpgFig. 4: ... then pull out the lock cylinder from the steering column
  1. With the ignition switch still in the ON position, insert a thin screwdriver into the slot adjacent to the switch attaching screw boss (right-hand slot). Depress the spring latch located at the bottom of the slot to release the lock cylinder.
  2. Remove the lock cylinder.
To install:
  1. To install the lock cylinder, turn the key to the LOCK position. Insert the lock cylinder in to the housing far enough to contact the drive tang. Force it inward and move the ignition switch actuator rod up and down to align the components. When the components align, the cylinder will move inward and the spring-loaded retainer will snap into place locking the lock cylinder in the housing.
If the lock cylinder is retained by a screw, tighten the screw to 40 inch lbs. (5 Nm).
  1. Install the key warning buzzer switch.
  2. Follow the ignition switch installation procedures to adjust the ignition switch.
  3. Install the turn signal switch.
With Air Bag
Please refer to the ignition switch removal and installation procedure.50c573d.jpg73cc55f.jpgb9448d0.jpg278f367.jpg

Oct 22, 2008 | 1990 Jeep Cherokee Limited

1 Answer

Oil warning light problems


Hi sam,
  • Turn off the ignition
  • Press and hold the button on the left side of the display while turning the ignition on
  • Service OIL will be displayed
  • Pull out the button on the right side of the display until the service prompt is cleared
  • The display should now read ---
If the above procedure does not work, outlined below is an alternative procedure:
  • With the ignition off, push the right button
  • Turn the ignition on and then pull the left button
  • This should clear the warning message
ttt

Oct 14, 2008 | 2001 Audi A4

1 Answer

I have a 2000 passat. We changed the brakes and now the ABS warning light, buzzer and "service manual" keeps coming on the dash. Any ideas what it might be?? Thanks


To stop the service interval warning and sound coming on please follow the following steps.
1. insert key into ignition. 2. using right hand press and hold the odometer reset stalk. 3 using your left hand turn on the ignition ( dont start the Car) 4 now use your left hand to press the clock adjust stalk and turnit to the left. ( just advance the time by 1 minute) 5 release both stalks and then turn ignition off , then on again and your service warnig light and sound will now not appear for the next 5000 miles. ( repeat the above when it comes on again) This will also save you £30.00 for the garage to do it.

Jul 28, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
2005 Pontiac Sunfire Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...