Question about Peugeot Cars & Trucks

Open Question

Center console removal

Fob has fallen inside need to remove center console to get to it

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: I need to remove the drivers internal door panel

Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Posted on Feb 22, 2009

GM Elec
  • 1000 Answers

SOURCE: need instructions on how to remove center console to access electric window switch.

Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.

  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

Posted on May 04, 2009

  • 2 Answers

SOURCE: How to remove center console or where to get the diagram? Thanks Tony

In my 2004 Sierra the console is held in by the seat bolts. You will need a star 16 and 20 to get the seats out. There are 2 bolts that go into the dashboard also. There is a big electrical connection under the console that needs to be unplugged to get it out.

Posted on May 23, 2009

alwynblack
  • 15 Answers

SOURCE: how do i remove the center console in a mercedes

take out your ashtray and see if there is srews down there and remove the cover round the gear shifter to find the other srews

Posted on Jul 19, 2009

  • 2 Answers

SOURCE: how to remove jaguar center console

As in you want a diagram? Either way, I don't have one but I have managed to remove it. I don't know if this might help but I start off by forcibly removing it by holding on to both sides of the top of the console (where the ash tray resides). Upon removal, I remove the cover of the ash tray by unscrewing two screws on both sides of the cover. These require a cross screwdriver. I then take off the connectors to both of the buttons where the gear lever is. The leather surrounding the handbrake is a bit tricky to remove. Slowly unbutton it then remove the top plastic part; you might lose the little spring that holds the button if you aren't careful. Then open the arm rest. Two Torx screws are located by the pivot point of the arm rest. I'm sorry I can't remember the size (most likely an T8). That's just about it. Hope this helps

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove the center floor shifter console on a automatic 2005 chevy aveo


The center console needs to be removed, pull the shift plate plastic cover off,
remove two bolts inside the console storage box,
remove the fillips screws that are visible,
the front center storage box also has to be removed,

Feb 26, 2013 | 2005 Chevrolet Aveo Sedan

1 Answer

2005 aveo chevy How do I take the console off


The center console needs to be removed, pull the shift plate plastic cover off, remove two bolts inside the console storage box, remove the phillips screws that are visible, the front center storage box also has to be removed, the bulb is located on the left side of the shifter from underneath.

Feb 26, 2013 | 2005 Chevrolet Aveo

1 Answer

2010 honda pilot center console removal due to vibration underneath


slide both seats all the way forward remove screws in sides of console if no screws on sides slide seats back and pull center from inside remove two bolts remove side skirt on each side screws under them remove ashtray center pocket screws under it also unplug wire connectors and remove

Jul 29, 2012 | 2010 Honda Pilot

1 Answer

The emergency brake handle in the center console is being obstructed by something that has fallen into the console. How can I take the console off so I can clean it out and free the brake handle's...


there will be plastic caps covering bolt holes.... might be easiest with seats removed.but the cover is attached at the bottom to hangers.

Feb 12, 2011 | 2000 Ford Contour

1 Answer

How do I remove the center console of a 1994 Buick Regal in order to repair the light gauge showing drive, reverse, neutral etc? (The plastic pieces on both the automatic shift lever and the indicator...


You should be able to remove the trim plate that where the shifter is, it the cover and from there you will be able to replate the bulb for the selector window,

Aug 29, 2010 | 1994 Buick Regal Gran Sport

1 Answer

Light bulb is burned out on gear shift console. How to remover cover?


The center console needs to be removed, pull the shift plate plastic cover off, remove two bolts inside the console storage box, remove the phillips screws that are visible, the front center storage box also has to be removed, the bulb is located on the left side of the shifter from underneath.

Hope helped with this (remember rated this help) Good luck.

Nov 11, 2009 | 1995 Toyota Corolla

1 Answer

1993 Volvo 850 How do I remove the Center Console


if you cant find any plastic that pops out and has screws underneath carpet inside center console if any, try pulling the switch itself and or assembly out. hit contacts with an eraser. and your favorite stuff. get a good manual.

May 24, 2009 | 1993 Volvo 850

1 Answer

1996 accord center console


If your vehicle is an automatic, it should light up your console where the gears are marked. There's a bulb under the console. in order to get to it, you'll need to empty the console and remove the plastic piece covering the screws (very bottom of console middle) and remove the screws. Then you'll need to remove the drink holder (pops out) and remove the screws under it. Lift the rear piece of the console over the E brake, and loosen the screws to the piece with the gear indicator. You should be able to see the lamp holder and twist lock connector. If the connector hasn't just fallen out, replace the bulb and twist the connector securely back into place.

Feb 21, 2009 | 1996 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...