Question about Cars & Trucks

1 Answer

How do u replace fuel filter ford ranger xlt 1997 6 cylinder

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 191 Answers

Hi lisleyholt34,maybe you should read this article,How to Replace Fuel Pump and Fuel Filter.

Posted on May 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75077 Answers

SOURCE: starter stays engaged

The starter relay on the fender is the most common cause of this condition. ,It is on passenger side feder in the engine compartment, it is round and the positive cable of the battery goes to it,

Posted on Nov 13, 2008

alicantecoli
  • 22095 Answers

SOURCE: 1986 ford ranger xlt 2.9 liter fuel injected

thermostat or blocked matrix in rad,evan head gaskets could be on the way out

Posted on Dec 25, 2008

  • 74 Answers

SOURCE: 1998 ford ranger xlt

p0102= mass air flow sensor is dirty or needs to be changed.
p0232= recheck your wiring. you might have crossed wires when changing fuel pump or your fuel sensor might be faulty

Posted on Feb 18, 2009

  • 13 Answers

SOURCE: where is the fuel pump reset switch in a 1997 ford

fuel pump shut off switch and reset is located on the right hand side floor board underneath the floor carpet, just pull carpet back.

Posted on Sep 26, 2009

SOURCE: My 98 ranger is still misfiring on cylinders 2 and

most likely the coil or ignition module

Posted on Dec 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuel filter located. Can this be easily replaced or does a shop need to replace it? (1987 Ford Ranger XLT V6)


That depends, some have filters in the tank. But most of them are under the truck running along the frame. You should be able to get a haynes or chiltins manual and it will tell you where it is.

Apr 16, 2011 | 1987 Ford Ranger

2 Answers

Locate Fuel Filter on 2005 Ford Ranger XLT


on my 05 ranger v 6 single cab the fuel filter is located on drivers side mounted in the frame.

Oct 09, 2010 | 2005 Ford Ranger

1 Answer

Fuel filter installation on 1990 ford ranger xlt


It's on the driver side just behind the door. You need a special tool to pull the lines off of the existing filter. It seems to be a cheap simple tool. it slips over the line then you push toward the filter, it will click then you can pull the line off. Just pull the lines then replace with the new filter. The truck will start funny at first because it will be deprived of gas for a moment but then it should be fine.

HTH, Mike...

Dec 07, 2009 | 1990 Ford Ranger SuperCab

1 Answer

Where is the fuel pump reset switch in a 1997 ford ranger xlt


fuel pump shut off switch and reset is located on the right hand side floor board underneath the floor carpet, just pull carpet back.

Sep 25, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Can I add an extra fuel tank to my 2000 Ford Ranger (XLT, six cylinder, extended cab)?


yes. but you'll need another fuel pump. go with a universal in line. you won't have the psi for both of them with your fact. pump.

Aug 30, 2009 | 2000 Ford Ranger SuperCab

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...