Question about Cars & Trucks

1 Answer

Ford e350 electrical schematic

1999 E350. Turn key, click but no start. New battery, replaced ignition lock cylinder, no joy. With old switch used to be able to jiggle steering wheel/shift lever and sometimes get results. Ideas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Did you replace the ignition lock, or switch ?
Will it crank if you jumper the solenoid for the starter ?

Posted on Feb 15, 2014

Testimonial: "Replaced the key cylinder column "switch" that releases by pressing a ball through the hole in the column plastic shrouding. Haven't yet tried jumping the solenoid. May be able to give that a shot tomorrow, depending on the weather (van is outside and I'm in the Midwest."

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 407 Answers

SOURCE: 2000 Ford E350 Econoline, 5.4L. Won't start.

neutral safety switch also if the shifter handle is real loose the assm might be bad there known to break or the bushings to get warn out.

Posted on Oct 21, 2009

flacooo1
  • 172 Answers

SOURCE: 1998 nissan altima gxe -ignition problem

Hi what is happening is that your turn off your car and left the wheels turned to one side and specially if your car is parke in a hill what you have to do is to force the steering wheel to the same direction of your wheels this will free up the ignition switch it is going to be hard let me tell you but it will work and this is why your shift don't work once you have the ignition switch free then your shift will work again

Posted on Apr 01, 2009

inspectmycar
  • 233 Answers

SOURCE: I REPLACED THE STEERING COLUMN

If you do not have a pass key any more, then you will need to dissable the antitheft (pass key module) in order for the engine to turn over. From what I gather you have replaced the column with an older version, which will not allow any comm. with the module. The pass key module enables the starter circuit. See diagram.


024620b.gif

Posted on Sep 27, 2009

Testimonial: "" Right on man!! You gave me the info I needed. THX "

  • 312 Answers

SOURCE: Key win't turn ignition switch in 2008 Chevy HHR

replace the floor shifter. there is a switch on the shifter that allows the key to move. gm has had alot of problems with these shifters.

Posted on Dec 27, 2009

  • 3 Answers

SOURCE: 2004 Volvo XC90. Ignition key will sometimes not

spray ignition with graphite

Posted on Jan 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 ford econoline e350 wont turn over


something wrong with the ignition switch?

Mar 30, 2014 | Ford E350 Cars & Trucks

1 Answer

2001 ford focus


If your Ford Focus is not starting, and you know the battery and alternator are good, the problem could lie in the ignition system. The ignition switch is a whole cylinder inserted into the steering column that connects to the starter motor. When you change an ignition switch, you are also replacing the key.

  1. Remove the dashboard panel below the steering column in your car; it should be screwed in place. Remove the steering column's upper cover by releasing its clips with a flat-head screwdriver.
  2. Look for the audio control switch---a small device sticking out of the steering column that acts like a remote control. If one exists, release the switch's plastic locking tang with the screwdriver, and unplug the electrical connector to remove the switch.
  3. Loosen the steering column by releasing the locking lever, and remove the steering column's lower cover by pulling out the screws with the screwdriver.
  4. Use your ignition key to turn the switch to the left---the position that would activate the accessories but not start the car. Insert the screwdriver into the hole in the top of the cylinder to depress the detent spring, and pull out the cylinder with the key inside.
  5. Insert the new key into the new ignition switch, and line up the switch inside the steering column so it's in the same place the old switch was in when you removed it. Make sure the detent locks into place; then turn the switch so it's in the "Off" position.
  6. Replace all the covers and panels you removed to access the cylinder, along with the audio control switch, if applicable, in reverse order of

Things You'll Need:
  • Small flat-head screwdriver
  • Ignition switch and key

Tips & Warnings
  • Older Ford Focus models may have a different method of removing and changing the ignition switch. Check an automotive guide for your particular year and model.
  • Always disconnect the negative (black) battery cable before working on the ignition or any other electrical component of your car.

I hope helped with this (remember rated this help) Good luck.

Nov 11, 2009 | Ford Cars & Trucks

1 Answer

Need to replace 1997 e350 ford Ignition ,how can i


you dont have to remove the steering wheel on a most Ford car and trucks you insert the key turn to the on position and there is a small pin under the ignition switch that you push and it comes right out.you have to remove the steering wheel cover above and below the ignition switch.

Oct 04, 2009 | 1997 Ford F350 Crew Cab

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...