Question about 2008 Jeep Patriot 2.4

Open Question

Remove starter on 2.4 2008 patroit

Show diagram

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the starter for my 2006 Chrysler Sebring touring


You'll need a set of metric sockets and end wrenches. Then disconnect the positive battery cable. Wrap the terminal you removed from the battery in a rag and secure it away from the battery. Follow the positive battery cable down to the engine block. It will most certainly be connected to the starter. Remove the cable and any other small wires. Make a diagram showing where to reconnect them. Remove 2 14 mm bolts from the starter to bell housing. Remove starter. Reverse the procedure to install new one.

Jan 26, 2015 | 2006 Chrysler Sebring

2 Answers

How to remove a starter on 1987 buick park avenue


show me a diagram with the location of the starter

Jul 14, 2014 | 1987 Buick Electra

1 Answer

How to remove a dash from a jeep patroit 2008 ,to install the a/c evaporator


most individuals dont have all those tools on hand to do this..either take it to a shop and let them deal with it or to the dealer service.. then you wont have the headache of keeping all those fasteners in line..

Dec 28, 2013 | 2008 Jeep Patriot

1 Answer

Cant remove my starter from 1997 fordareostar


CAR STARTER REMOVAL? TESTING


One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----


How to test starter solenoid? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html -------------------- How to test cars starter? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html ----------- How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------
How to replace Starter on Infiniti Q45? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------
2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----
Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

Oldsmobile starter solenoid replacement procedure?...

--------------------

How to replace Oldsmobile starter moor?

----------

Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

Nov 26, 2012 | Cars & Trucks

1 Answer

Remove and replace starter


Replacing starter is not a difficult job.The vehicle needs to be lifted up on jack stands.The starter needs to be accessed from under the car. --------- You need to remove the air filter housing and intake, and the battery and tray if you want to make it easy on yourself. Remove those first, then remove the top starter bolt before you go under the car.

Accessing the top starter bolt,sometimes takes time. The top bolt comes from the transmission side on top.
-----------
Click this link below to see diagram showing location of top bolt:--- http://technoanswers.blogspot.com/2011/10/how-to-replace-starter-on-2000-mazda.html --------- This will help.Thanks.Helpmech.

Oct 07, 2011 | 2000 Mazda Protege

3 Answers

I AM TRYING TO REPLACE MY STARTER ON A 1997 CHEV LUMINA 3.1 V6. I NEED A DIAGRAM OF THE STARTER


Hello Larry...Here are the steps to take. Detach the ground (black) battery cable. Lift the front of your vehicle with a floor jack, support it with jack stands and chock the rear wheels.
Unfasten the retaining nuts holding the heavy (battery) cable and the thin wire to the back of the starter solenoid (the small cylinder mounted on top of the starter motor) with a wrench. Move the heavy and thin wires out of the way.
Loosen the two mounting bolts holding the starter motor to the engine block with a ratchet, large ratchet extension and socket. Hold the motor assembly with one hand and finish removing the two starter mounting bolts. Make a note of the position of each mounting bolt, since they are of different sizes, and of any shims located between the starter motor, mounting bolts and engine block.
Remove the starter motor from the vehicle

To Install:
Position the new starter motor in place with one hand and install the two mounting bolts finger tight with your free hand, along with any shims installed with the original starter. Failing to replace the shims may cause the starter to grind against the flywheel or engage and fail to start the engine

Tighten the two mounting bolts with the ratchet, extension & socket.
Install the heavy cable and wire in their respective mounting studs at the back of the starter solenoid and install the retaining nuts finger tight. Tighten the nuts with the wrench; (careful not to overtighten)
Lower your vehicle off the jack stands...Attach the ground (black) battery cable.

There you have it, included is a picture of the starter, good luck, i hope this helps.

http://www.autopartswarehouse.com/sku/Replacement/Starter/REPB320102.html?tlc=Engine+%26+Drivetrain

Jul 29, 2011 | 1997 Chevrolet Lumina

1 Answer

Do you have a diagram of the engine of the 2002 Kia Spectra because I need to replace the starter


You don't need a diagram.Lift the car disconnect the battery and the wires to the starter solenoid remove the starter bolts and check the shims placement.Replacement starter is reverse to what is listed in removal

Sep 28, 2009 | 2002 Kia Spectra

2 Answers

Where can i find a diagram that shows the starter location


The starter is below lower side of the engine, either at the r/h lower side or l/h lower side were the transmission mounts to the engine.

Aug 08, 2009 | 1997 Chrysler Sebring

1 Answer

Diagram needed


you really don't need one.....
1.Disconnect the battery
2.locate the starter. If its a v8 itll be on the driver side at the back of the engine beside the oil pan
3.there are two bolts on the bottom of the starter that you need to remove with a 9/16 socket or wrench.(support the starter when you remove the last bolt so the wires don't get broken)
4.observe the location of all of the wires attached to the starter(make a diagram so you don't forget where they go)
5.Remove the nuts that hold the wires on the starter.(make sure the ring connectors and wires are in good shape if you notice any damaged ones they should be replaced)
6. reverse procedure to install new one
..............hope this is helpfull.good luck!

Dec 10, 2008 | 1995 Chevrolet Lumina

3 Answers

Remove starter motor


leave car on the weel,s lift up the engine couple of inches till you have clearance to pul starter out .(have to wiglle litlle bit ) .In most cases problem on starter is copper contacts on solenoid,order repair kit on ebay for 25 $ rebuild solenoid ,put it back . You save yourself 175 $..

Aug 02, 2008 | 1998 Isuzu Rodeo

Not finding what you are looking for?
2008 Jeep Patriot 2.4 Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...