Question about 2008 Ford Taurus

1 Answer

Removal and replacement of external rearview mirror

My mirror is electric with a manual fold. It is not heated

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Ford Expert
  • 496 Answers

Remove the inner door panel and unbolt the mirror and disconnect the wire connection. Replace in opposite order.

Posted on Feb 02, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 37 Answers

SOURCE: Replacing the passenger side mirror

screw driver will work then there will be 3 10mm nuts

Posted on Sep 25, 2008

  • 2920 Answers

SOURCE: rearview mirror on a 1998 ford exployer

o to the auto parts store and buy a rear view mirror ask them for the rearview mirror adhesive and on the back of the package it tells you how to use it.its not very hard to do and isntexpensive to buy. takes about 15 minutes

Posted on Jan 18, 2009

  • 11 Answers

SOURCE: fiesta 06>08 electric/folding mirrors online wiring diagram

ford etis online

Posted on Mar 07, 2009

  • 708 Answers

SOURCE: removal of the mirrors plastic body from the truck

I did the same thing with my car. there is a plastic cover inside the door where the mirror is. Pop off the cap and you can then take off the mirror. ONly problem is you can not change just the mirror you have to replace the body too. At least thats the way it was on my car. Dealer part was $137 at the time and it wont be painted.

Posted on Jul 25, 2009

  • 45 Answers

SOURCE: hot to install driver's side rearview mirror '98 Expedition

3 10mm nuts located behind the interior door panel (directly behind the mirror assembly) attach the mirror to the door. Also there you will find the point of attachment for the power as well.

Posted on Oct 01, 2009

Testimonial: "Thank you for verifying the procedure. I thought to myself it can't be this simple when I looked at it so I wanted make sure being a novice at this."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 gmc heated mirror module


Could have a DDS an PDS .depends on what RPO code yours has >
Outside Mirror Description and Operation (with RPO DL3)
Or
Outside Mirror Description and Operation (without RPO DL3)
Without
Heated Outside Rearview Mirror Operation
The REAR DEFOG relay controls the operation of the heated outside rearview mirrors. When rear window defogging is requested, the REAR DEFOG relay is energized and B+ is applied to the supply voltage circuit of the mirror heater element, located in the mirror face. A constant ground is also applied to the mirror face. Current will pass through the mirror heater element, warming the mirror, so long as the rear window defogger is commanded ON.

With
Heated Outside Rearview Mirror
The DDS and PDS control the activation of the mirror heaters. Upon receiving a serial data message indicating a request for heated mirrors, the DDS and PDS, will apply voltage to the mirror heater element supply voltage circuit. The mirror heaters will remain active until a new message is received indicating rear defogger is to be deactivated.
The power mirror system consists of the following components:
• Driver Door Switch (DDS)--An electronic control module with integrated switches and requires programming when replaced
• Passenger Door Switch (PDS)--An electronic control module with integrated switches, requires programming when replaced
• Power Mirror Direction Switch--Integrated into DDS and is a four position momentary switch that provides a signal input to the DDS for up, down, left/extend and right/retract with a mirror switch activation
• Mirror Select Switch--Integrated into DDS and is a three position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• Mirror Extend/Retract Switch--Integrated into DDS and is a two position switch that allows the operator to select the mirror extend or mirror retract position
• Left Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Right Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Body Control Module--An electronic control module that requires programming when replaced, serves as the power mode master and is the main message handler
• Horizontal and Vertical Position Sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDS/PDS and provide a variable voltage signal to the DDS/PDS that is proportional to mirror position
• Folding Mirror Motor, in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Your best bet mite be to take to a qualified repair shop , i really don't think you'll be able to do anything with it.
Do you have wiring diagrams so you know which wires to test ,do you know how to do electrical testing ?
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) supply voltage to the outside rearview mirror heater elements upon receipt of a serial data message from the HVAC module indicating that the rear defrost system is active. The door switch supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen. Ground is applied through the driver/passenger mirror heating low reference circuit.

Sep 15, 2017 | 2007 GMC Sierra 2500HD

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How to replace a broken wing mirror on a Volvo S40 1980 model



Power Dr Mirrors Diagnosis & Testing


Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Disconnect the negative battery cable. The mirror inside cover trim The door panel The electrical connector to mirror motor The nut attaching mirror assembly to door frame The outside rear view mirror

    0900c152801c11d4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing cover trim and nut
    Removing cover trim and nut

    0900c152801c11d5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing mirrored glass from assembly
    Removing mirrored glass from assembly

  3. Remove the mirror glass:
    1. Fold the mirror glass forwards and inwards as illustrated.
    2. Grasp and pull the mirror glass lengthways until it releases.
    3. Work the glass out.

  4. Remove electric motor:
    1. Remove the 3 screws from behind the mirrored glass.
    2. Separate the connectors
      NOTE Remember the positions of the connectors.
    3. Remove the mirror motor.

      0900c152801c11d6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Removing connectors and screws holding mirror motor
      Removing connectors and screws holding mirror motor



To install:
  1. Install or connect the following:

    The electric motor The electrical connections The 3 screws that go behind the mirror Install the terminal pins Fold out the mirror mounting on the motor Hook the mirror glass into the inner mounting Press the mirror glass into place. Place mirror in position in door

    0900c152801c11d7.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Reattaching mirror and electric motor connectors
    Reattaching mirror and electric motor connectors

  2. Install or connect the following:

    The nut attaching mirror assembly to door frame The connector The door panel The mirror inside cover trim The negative battery cable

Oct 23, 2010 | 2000 Volvo S40

3 Answers

2004 ford expedition eddie bower


For the rear window, just need adjuts the both slightly...


Check the next procedure to Power Mirrors...

Diagnosis & Testing

The exterior mirror control switch receives power through circuit SBP12 (GN/RD) and ground through circuit GD143 (BK/VT). The exterior mirror control switch uses circuit CPM23 (GY) as the common circuit for both exterior mirror up/down and right/left movement.
  1. Possible Causes:
    Fuse 12 (7.5A) (SJB) An open in circuits CPM23 (GY), SBP12 (GN/RD) or GD143 (BK/VT A short to ground in circuit CPM23 (GY) A short to voltage in circuit CPM23 (GY) Exterior mirror control switch.
  2. Checking the voltage at the mirror switch:
    Key in OFF position. Disconnect: Exterior Mirror Control Switch C527. Key in ON position. Measure the voltage between ground and exterior mirror control switch C527-1, circuit SBP12 (GN/RD). Voltage should be greater than 10 volts.
  3. If voltage is greater than 10 volts, check that fuse 12 (7.5A) is OK. If OK, REPAIR circuit SBP12 (GN/RD) for an open.

Exterior Mirror Motor Synchronization

NOTE This procedure must be performed any time the power folding mirrors are manually folded in or out, or if the position of the mirror case has been moved without using the mirror control switch.
NOTE If the power folding mirrors are folded or unfolded continuously (6 to 10 cycles), the power lockout feature will disable the system for 2 minutes to prevent damage to the power fold motors. After 2 minutes have elapsed, normal operation will resume.
  1. Set the mirror control switch to the CENTER position.
  2. Use the mirror control switch (press rearward) to automatically cycle the power folding mirrors in and out 4 times.
  3. When an audible popping sound is heard, the power folding mirror motors are synchronized.
    NOTE It may be necessary to cycle the power folding mirrors in or out up to 4 times before they are synchronized.

Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the precautions section.
    NOTE If equipped with power folding mirrors, they must be synchronized any time the mirrors have been folded or unfolded without using the mirror control switch. Refer to synchronization procedure.
  2. Position the exterior mirror glass in a downward position to obtain a gap at the edge of the mirror.
    CAUTION Place a shop towel between the exterior mirror glass and the hand to avoid personal injury in the instance of glass breakage.
  3. Insert a flat-blade screwdriver between the mirror glass tabs and the mounting plate, and rotate to separate the locking tabs from the mounting plate.
  4. Carefully pull the top edge of the glass away from the exterior mirror housing.

    0996b43f802029e0.jpg Fig. Mirror Glass removal shown
  5. If equipped, disconnect the heated mirror electrical connectors and remove the glass.
  6. Remove the 3 exterior mirror motor screws and exterior mirror motor.
  7. Disconnect the electrical connectors.
  8. To install, reverse the removal procedure.

Switch
Expedition Trim Panel Removal

NOTE The door glass must be completely raised.
  1. Remove the window control switch plate.
  2. Remove the door handle bezel.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  3. Remove the two bolts and three screws, and remove the door trim panel.
  4. Remove the finish cover to access the two center screws.
  5. Disconnect the electrical connectors. Navigator Trim Panel Removal
  6. Remove the door handle bezel.
  7. Use service notch.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  8. Remove the two bolts and three screws, and remove the door trim panel.
  9. Disconnect the electrical connectors.
  10. Depress the locking tabs and remove the exterior mirror control switch.
  11. Remove the exterior mirror control switch.

If you dont want waiting more time for the Owners Manual, can check here this choice 2004-Ford-Expedition-Owners-Manual

Hope this help.

Apr 23, 2010 | 2004 Ford Expedition

1 Answer

2002 Mountaineer. How do you change the light bulb at the bottom of the driver side rear view mirror. Dan


SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.

NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
ed6be7c.gif
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Dec 26, 2009 | 2002 Mercury Mountaineer

1 Answer

Ford expedition side mirror (instalation giude)


SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.
  1. Remove the door handle bezel.
    • Use service notch.
  1. Remove the window control switch plate.
    • Use service notch and disconnect the electrical connectors.
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    Remove the two bolts and three screws, and remove the door trim panel.
  1. Remove the weather shield.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror.
    • Remove the nuts.
cf86471.gif
  1. To install, reverse the removal procedure.
    • Install top nut first.
---
Exterior Mirror Motor Removal and Installation
  1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.
  1. Disconnect the heated mirror electrical connectors.
  1. Remove the exterior mirror motor screws and exterior mirror motor.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.

Oct 26, 2009 | 2003 Ford Expedition

1 Answer

Mirror glass replacement on drivers side


i don't have aviator. here's explorer, should be the same.

You will see a small rectangle where the screwdriver goes in. You are pryingtowards glass. The retention is about a 3 inch rectangle that has a lip around it that snaps onto a rectangle on the mirror body.

SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released. (and pull screwdriver towards glass)
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Apr 18, 2009 | 2003 Lincoln Aviator

1 Answer

Replacement of Mirror/Assembly, 2004 Ford E350 Super Duty


Exterior Mirror Removal and Installation
NOTE: Aero mirror shown, dual arm similar.
Manual mirrors
  1. Remove the mirror sail cover to gain access to the exterior mirror retaining nuts.
Power exterior mirrors
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the front door speaker.
  1. Remove the front door watershield.
All exterior mirrors
  1. Remove the rubber plugs and dust shield.
Power exterior mirrors
  1. Disconnect the electrical connector(s).
    1. Disconnect the power exterior mirror electrical connector.
    1. If equipped, disconnect the heated exterior mirror connector.
All exterior mirrors
  1. Remove the nuts and remove the exterior mirror.


  1. To install, reverse the removal procedure.
  2. 01cb1f9.gif

Jan 08, 2009 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

Interior rearview mirror anti-glare failure


The mirror is toast. There is no fix for it.
It's about $125, new.
The clock is a seperate electrical issue. Also no fix.
About $73.

Jan 02, 2009 | 2002 Subaru Forester

1 Answer

Custom Rear view mirror


Hiya...ALL factory-installed rearview mirrors are installed with different wires due to options.
About 6 different rearview mirrors are installed with those options such as On-Star, light, compass, and those features which use different wires....THIS CANNOT be modified with different rearview mirror....**for example, the Equinox owner attempt to pull out a factory-installed base rearview mirror and put in different one that has compass/temperature built into the rearview mirror**

However, the wires are located inside the front headliner which requires removing the sunvisor (and possible removal of interior plastic trim part at the left/right ends of the windshield) prior to pull the headliner down, and a small metal philips or torx screw is used to secure the rearview mirror onto the bracket glued to the windshield.

The best solution is to leave the original factory-installed rearview mirror in place.

May 16, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
2008 Ford Taurus Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...