Question about 2002 Volkswagen Jetta TDI

1 Answer

How will i know if my needle lift sensor is broken

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Volkswagen Master
  • 733 Answers

WHAT DO U MEAN BY NEEDLE SENSOR?

Posted on Mar 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Had fuel level sensor replaced few years ago. today fuel gauge needle does not move and is positioned below the empty point. any ideas what may cause this?


It could be any one or more of this list:
Fuel level sensor. Just because you replaced it once, doesn't mean it's still good.
Connection to fuel sensor
Broken wire between fuel sensor and gauge
Broken wire between battery and fuel sensor/gauge
Bad gauge

Nov 03, 2015 | 2005 Buick Rainier

1 Answer

00542 needle lift sender int can anyone help me with this code on my audi a 6


code 00542 refers to injector needle lift sensor===causes--air in fuel system--fuel level low---wiring--- needle lift sensor . Check for air in the manifold and if ok the replace the sensor.

Apr 20, 2014 | 2002 Audi A6

1 Answer

Toyota Camry 2002 - Hood lift wire broken - Cannot open the hood. What to do ???


You can access the hood latch from the grill. With a pair of needle nose, and a screw driver you can manipulate the mechanism and open the hood. Good luck

Nov 09, 2013 | 2002 Toyota Camry

1 Answer

Vw p1247 code fix


P1247 Needle Lift Sensor Circ. Open/Short to B+

The needle lift sensor is part of injector #3. Check for damaged wiring or corroded wiring harness connector leading to that injector.

Apr 24, 2012 | Cars & Trucks

1 Answer

My 2003 Olds Shilouette air shocks work but the sensor for the load must be out. With a load the air compressor is not signaled to pump. The pump works when I activate the auxillary button. Where is that...


the load sensor is probably broken. It connects the rear axle to the frame to measure load. Its mounted on the left side of the rear axle. Its commonfor these to become damaged if the vehicle is lifted by the frame rather than by the axle. Looking at the part you will probably see the sensor arm hanging loose.

Nov 06, 2010 | 2000 Oldsmobile Silhouette

2 Answers

Need to know how to sweep or reset gas guage needle


I had the same make and model do this to me the other day. I had to remove the cover around the cluster and remove the clear lens, then move the needle around by hand. Then put is back together. It fixed it but what a pain.

Jun 06, 2010 | 1998 Chevrolet Malibu

1 Answer

Ground shielding wire for needle lift sensor?


Shielding wires are always only connected at one end. Connecting at both ends substantially reduces the protection offered.

Jun 10, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

1993 lexus LS 400 speedometer works sometimes


the plastic gear on speed sensor is broken , replace , this is on transm. rear case

May 31, 2009 | 1991 Lexus LS 400

1 Answer

Speedometer works sometimes on 95 neon


Common on those is the dash cluster connection itself, there is a plug on the back of it, that you pull off & i ended up using tweezers or needle nose pliers and just very slightly twisted or bent ends of the male spade (small) contacts on the cluster itself, one by one. re-attached everything & problem cured. If you just pull trim around the cluster, it will come off, then 3 or 4 screws and cluster will lift out of there, unplug harness, do as described & re-install. Let me know how you make out. Did it 2 or 3 times in my 95 neon & it cured it for a few years each time.

Jan 02, 2009 | 1995 Dodge Neon

Not finding what you are looking for?
2002 Volkswagen Jetta TDI Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...