Question about Chevrolet 1500

Open Question

Were is the starter relay located on vw passat vr6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1995 VW Passat Oil Pressure Sensor/Leak

ya honestly just fixed that on my 1993! its not a big deal but u got to break it lose with a 24mm deep socket and it works!

Posted on Jan 08, 2009

Ad
bunnydawg
  • 5158 Answers

SOURCE: need relay location

relay 1 engine compartment
fascia 2 relay 18 (if it is diesel) relay 10 (diesel again) and this could likely be the best candidate relay 4 fuel pump relay/glow plug relay

Now for the fuse box locations ... looking from the front of the car... the engine compartment fuse box is on the left side up near the firewall.
fascia two is the lowest of the two fuse panels on the drivers side under the dash to the right of the steering column (left if it was a right hand drive).

This took about 15 minutes to locate all the possible fuses, be that as it may if i missed it don't hesitate to ask me again.

Robert

Please take a moment to rate this solution thanks

Posted on Feb 17, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

  • 194 Answers

SOURCE: LOCATION OF FUEL PUMP RELAY ON 2003 VW PASSAT

Relay panel is under dash, drivers side. Theere are 3 rows of relays, you want the bottom row ,4th spot from the left (#208)?

Posted on Jan 05, 2010

  • 4102 Answers

SOURCE: I am having troubles locating

hi, here is a guide i have come across on this site written by another expert it should be the one for your engine but always double check.

If you are unsure what you are doing then please go out and buy a haines workshop manual as these tell you every detail you need to know so that would be your best solution.

Please dont do this work if your unsure what you are doing as you could damage the engine beyond repair so you have been warned;

it covers single cam and if you scroll down it shows double cam ok

Sep 14, 2009 - VW Passat & Audi A4 1990-2000 Repair Guide
Timing Belt - REMOVAL & INSTALLATION

2.8L SOHC (AFC) V6 Engine

  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. Remove the Crankshaft Position (CKP) sensor from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Loosen the tensioner roller and remove the drive belt.
To install :
  1. Install the timing belt over the sprockets, then the idler rollers and lastly over the tensioner.
  2. Install camshaft alignment tool holder Tool No. 3243 into the camshaft alignment flanges.
  3. Check and adjust the cam belt tension such that the upper left portion of the belt between the tensioner and the left cam gear can just be twisted 90° ( 1 / 4 turn).
  4. Tighten the cam belt tensioning roller to 33 ft. lbs. (45 Nm), and the camshaft sprocket bolts.
  5. The balance of the installation is in reverse order of removal.

2.8L DOHC 5V (AHA) V6 Engine
  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. On the cylinder block near the crankshaft, remove the sealing plug from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, insert a 2mm spring pin through the tensioner housing and tensioner plunger to secure it in place. When the plunger is secure, release the wrench tension.
  5. Remove the damper-to-crankshaft bolts and the damper.
NOTE It is not necessary to remove the center bolt when removing the crankshaft damper.
  1. Remove the serpentine belt idler and the crankshaft damper guard.
  2. Mark the running direction of the timing belt and remove it from the pulleys.
58637f8.jpg

Fig. Crankshaft pulley alignment location for TDC-Audi 2.8L V6 engines


d58d8c0.jpg

Fig. Left camshaft sprocket alignment position for TDC; right camshaft position is similar-Audi 2.8L V6 engines


934cbaf.jpg

Fig. View of crankshaft holding tool installed-Audi 2.8L V6 engines


9091ff0.jpg

Fig. View of camshaft locator bar installed-Audi 2.8L V6 engines


To install:
  1. Make sure that the camshaft pulleys and the crankshaft pulley are in alignment with TDC of the No. 1 cylinder's compression stroke.
  2. Install the timing belt; make sure the timing belt is installed in the correct running direction from which it was removed.
  3. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, remove the 2mm spring pin from the tensioner housing. Slowly, release the tensioner spring pressure to put pressure on the timing belt.
  4. Install the crankshaft damper guard and the serpentine belt idler pulley; torque the idler pulley bolts to 33 ft. lbs. (45 Nm).
  5. Install the crankshaft damper and torque the damper-to-crankshaft bolts to 15 ft. lbs. If the damper-to-crankshaft center bolt was removed, torque it to 147 ft. lbs. (200 Nm) plus 180° 1 / 2 turn).
  6. Remove the Crankshaft Holder tool No. 3242 and install the sealing plug.
  7. Replace the remaining components by reversing the removal procedures.
  8. Refill the cooling system and the automatic transaxle. Connect the electrical connectors. Install the negative battery cable last.
  9. Test drive the vehicle.

Posted on Jan 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 vw passat v6 where is the fuel pump relay


The fuel pump relay is #4, counting from the left on the top row of relays. (accessible from under the dash) It should have a control # XXXXX 208 printed on top.

Oct 18, 2014 | Cars & Trucks

2 Answers

1995 volkswagen passat vr6 wont start the injectors are getting fuel but its not getting fuel to the engine. The injectors are getting spark and the fuel pressure is good.


if it fires then dies, you have to reset the alarm system with the key/remotes???otherwise you need to plug in the diagnostic computer(saves hours of "fun")

Jul 27, 2010 | 1995 Volkswagen Passat

1 Answer

1996 VW Passat VR6 is overheating, upper hose is hot, lower hose is cool, fluid is not leaking out. What do you recommend?


Thermostat is most likely. Try that first, then my next choice would be water pump. Good luck.

Mar 14, 2010 | 1995 Volkswagen Passat

2 Answers

LOCATION OF FUEL PUMP RELAY ON 2003 VW PASSAT


Relay panel is under dash, drivers side. Theere are 3 rows of relays, you want the bottom row ,4th spot from the left (#208)?

Jan 04, 2010 | 2003 Volkswagen Passat

1 Answer

95 passat vr6 giving problems


Adjust or replace the shiftlock sensor. It unlocks the shifting mechanism when you put your foot on the brake.

If there is an ignition problem, the tumbler will need replacement soon. This can be caused by an overloaded keychain. Best to do it now while it still is working, then have it fail and leave you stranded.

Jan 17, 2009 | 1995 Volkswagen Passat

2 Answers

Thermostat for vw passat 1995 vr6


I have found the thermostat- it is located at the right end of the engine block- up high- follow the radiator hose from the radiator to the engine- the thermostat is right there. There are 3 allen-head screws (5mm hex) that attach the thermostat cover to the thermostat housing. The issue I am having is that I can't reach on of the screws. I need help.

Jun 21, 2008 | 1995 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...