Not firing,, Nothing

theres no distributor and the firing order for your 3.8 is 1-6-5-4-3-2-the following link shows the coil pack
Buick General Motor 3800 V6 Engine Firing Order DIS IDI ignition timing 3.8 Buick Engine Coil Pack Firing Order Spark Plug Wire Location Which way do the spark plug wires go on & what cylinder is what?
.
For the Buick V6 231 3.8 liter turbocharged engine:
.
Answers!
.
Firing order:
1 - 6 - 5 - 4 - 3 - 2.
.
Spark plug wire location on coil pack:
.
Closest to the back of the car, left to right: 1 - 5 - 3.
Closest to the front of the car, left to right: 4 - 2 - 6.
.
Spark plug wire location on engine:
.
drivers side, front to back of car: 1 - 3 - 5.
passenger side, front to back of car: 2 - 4 - 6.
.----and this link shows the coil pack to cylinders
.
3 8 Buick Turbo Engine Coil Pack Firing Order Spark Plug Wire Location

I have had lots of these bikes, even though you see fire, put the plug in coil wire, and hold spark plug-kick over with other hand,yea if it knocks heck out of ya you know mag, and cdi box is good. If you only feel a lil nothing to big get a cdi box new. Now you say its getting fuel. when you choke it should show fuel on plug. You need to take carb back off to see if the power reeds are good, or got damaged when you took off carb to rebuild. good luck guys 2 strokes rule....................

have you checked the plug wires ?

Mark the one not firing. Now swap it out with one that fire. Does it fire now. If No then you will need a new CDI.If it doesnt then you have a wire issue. also check spark plug wires.

Ground the lead from a test light and then use the test light to the check the (-) negative side of the ignition coil and when the engine is cranking over the test light should flash or blink off and on rapidly indicating that there is a dwell signal to the ignition coil, and if the test light does not flash or blink then there is either a problem with the pick-up coil/stator located inside of the distributor, or there is a damaged wire somewhere in the ignition system between the pick-up coil/stator inside of the distributor and the computer, or between the (-) negative wire to the ignition coil and the computer.

Also be sure to remove the distributor cap and have someone turn over the engine and be certain that the ignition rotor does in fact turn, and that there are no blown out fuses that run the computer.


Pick-Up Coil/Stator

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
   NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
2. Remove the intake manifold cover, if required.
3. Disconnect the left side spark plug wires from the spark plugs.
4. Disconnect the left side spark plug wires from the ignition coil.
5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
6. Remove the spark plug wire assembly.
7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
8. Disconnect the right side spark plug wires from the spark plugs.
9. Disconnect the right side spark plugs from the ignition coils.
10. Remove the spark plug wire assembly.
11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.

To install:

1. Install the spark plug wire assembly.
2. Connect the right side spark plugs to the ignition coils.
3. Connect the right side spark plug wires to the spark plugs.
4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
5. Install the spark plug wire assembly.
6. Connect the left side spark plug wires to the spark plugs.
7. Connect the left side spark plug wires to the ignition coil.
8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system


Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system


I really hope help you with this (remember rated this help) Good luck.

check wires an plugs also

If the hi-tension wires check out ok you may want to check on the distributor and the contacts at its end and in the inside. You may also want to test the ignition coil.

Where is the cdi box located??

Start by checking if it's a fuel or fire problem. Take a plug wire off and turn motor over.If there is fire, Take the hose going from the air cleaner to the throtle body off and spray a small amount of carb. cleaner in.If it's a fuel prob.,check the fuel pump relay (under the hood in a black box) (swap the relay out with another relay in the box ) If the relay is o.k., it's probly the fuel pump. If it;s a fireing prob., start with the coil and wires going to the coil.