Question about 2004 Hyundai Elantra

Open Question

Need torque sequence and torque setings for 2.0 hyundai elantra head

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ghost4548
  • 776 Answers

SOURCE: i have a 1997 hyundai elantra 1.8 i need torque specs. for head

go to http://www.hmaservice.com/ and register. After that, you'll have access to manuals, service bulletins, wiring diagrams, etc.

Posted on May 28, 2009

Ad
  • 1071 Answers

SOURCE: Please provide torque settings for the head bolts

1st stage 45lbs then 65 then 85

Posted on Aug 21, 2009

techbuster
  • 5081 Answers

SOURCE: whats the torque for the head bolts on a 98

The cylinder head bolts need to be torqued at

  • 10MM bolts 22 FT-LBS
  • 12mm bolts 26 FT-LBS

Posted on Jan 20, 2010

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

  • 306 Answers

SOURCE: how to install head torque for hyundai 2005

4 cylinder? 10 bolts? This is generic. Starting in the center, top first then bottom, move over one position left or right top then make an "X" to the opposite side bottom. Then up and "x" back to bottom. One more "x" pattern for four remaning outside bolts. Final torque around 60 ft/lbs (generally)
Curious, how are you doing this without a repair manual? Tisk tisk.

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CYLINDERHEAD BOLTS TORQUE SEQUENCE HYUNDAI ELANTRA


Install the gasket so that the surface with the identification mark faces toward the cylinder head.
Tighten the bolts to the specified torque in the sequence shown below.
b176b2ac-2453-4b5b-9b1d-0cb775cacffe.jpg

Aug 04, 2014 | 2001 Hyundai Elantra

2 Answers

2001 hyundai elantra head bolt head torque specs


18-22 lbs step 1 .....step 2 60degree turn ...........step 3 60 degree turn

Mar 25, 2013 | 2001 Hyundai Elantra

1 Answer

What is the torque sequence on a 1996 Hyundai Elantra 1.8 dohc


  • Hi, I can help.
  • The torque sequence for the head of a 1996 Hyundai Elantra 1.8 dohc is indicated in the diagram below as well as the torque specs I have listed.

  • M10 bolts tighten to 22 foot lbs.
  • M12 bolts tighten to 26 foot lbs.



ironfist109_235.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Aug 18, 2011 | Hyundai Motor 1996 Elantra

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

Torquing down the cylinder heads


Generally you torque them all down once in sequence and do it once more to check for good measure to have them all correct

Jun 05, 2010 | 1997 Hyundai Elantra

2 Answers

Whats the torque for the head bolts on a 98 hyundai elantra


The cylinder head bolts need to be torqued at

  • 10MM bolts 22 FT-LBS
  • 12mm bolts 26 FT-LBS

Jan 20, 2010 | 1998 Hyundai Elantra

1 Answer

I need the cylinder head torque settings for 1997


1998 Hyundai Lantra "G4GM" engine 1795cc.there are two heads or blocks, one is called the M10, other is the M12, figure out which one you have cause the torque is different for stage one by 5nm........... Dont get confused theres 2 different engines so 2 different torques for stage1---------
heres the full details: Stage 1 - m10 = 30nm / m12 = 35nm-------------------------- -------- Stage 2 - tighten by 60-65 degrees ------------ stage 3 - tighten by 60-65 degrees. no sequence is given in the data book for tightening so go off what you thinks right, it doesn't matter on this engine.

Nov 17, 2009 | 1997 Hyundai Elantra

1 Answer

I need to know how many foot punds the head needs


the m10's bolts are 18ft.lbs. + 60-65 degrees extra of a turn and the m12 bolts are 22ft. lbs. + 60- 65 degrees of an extra turn.

do you have the tighten sequence? if not then from the top row left to right will go 7 , 3 , 1 , 6 ,10 and the bottom row left to right 9 , 5 , 2 , 4 , 8

if you don't understand let me know and if you have any more question please ask. good luck

Sep 25, 2009 | 2001 Hyundai Elantra

2 Answers

Hyundai elantra 1.6GLS J2 torque settings


dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

Aug 31, 2009 | 1995 Hyundai Elantra

1 Answer

I have a 1997 hyundai elantra 1.8 i need torque specs. for head


go to http://www.hmaservice.com/ and register. After that, you'll have access to manuals, service bulletins, wiring diagrams, etc.

May 17, 2009 | 1997 Hyundai Elantra

Not finding what you are looking for?
2004 Hyundai Elantra Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...