Location of speed sensor

https://www.google.com/search?q=2007+Ford+Focus+speed+sensor+locations

Where is the 2007 ford focus speed sensor located?

Vehicle History https://www.vehiclehistory.com > questions > where-is...
Located on the right side of the transmission near the output shaft. Like. (1). Leave your answer.
2 answers · Top answer: The 2007 Ford Focus speed sensor is found by watching: https://www.Youtube.com/watch?v=jxqItE9OI20 You will come into many issues with an engine. A gasket ...

2007 Ford Focus Sensor Locations

Rick's Free Auto Repair Advice https://ricksfreeautorepairadvice.com > 2007-ford-foc...
Oct 3, 2018 - Wheel Speed Sensor (Left Rear) (Wagon) At left rear wheel. Wheel Speed Sensor (Left Rear) (3 Door) At left rear wheel. Wheel Speed Sensor (Left ...

press the helpful button and follow me on fixya for more tips
Input speed sensor is located inside the transmission. The sensor is located next to the sprocket for the input shaft. The sensor is held in place with 2 6mm bolts, one for the sensor, one for the wiring harness.

Input Speed Sensor P0717 Replacement

P0717 ISS Speed Sensor Code Cadillac Deville Eldorado Seville Fleetwood...

Vehicle Speed Sensor Removal Installation

The transmission sensor or speed sensor is located in most vehicle located on the transmission case.These speed sensors are driven by a gear located on the output shaft. The speed sensor's driven gear can be either machined or fastened by a clip. The driven gear is made by plastic to make it softer than the drive gear. It's located on the end of the vehicle speed sensor.

The speedometer sensor is located on the top of the transmission. It is held on by one bolt. Remove the bolt and gently pull and turn the speedometer sensor and the whole assembly will come out of your transmission.


Park your Honda Prelude on a level surface, activate the emergency brake and place blocks behind the back tires for safety. Disconnect the negative battery cable with a terminal puller.

Raise the vehicle on the side of the wheel speed sensor's location. Remove the wheel and tire assemblies.

Disconnect the sensor electrical connection from the wiring harness.

Take note of the connection location for the sensor retainers, grommets and clips. You will need to know this information for the installation process.

Start at the connector end of the sensor cable and remove grommets, clips and retainers in order to free the harness.

Unscrew the sensor mounting bolt and remove the sensor from the differential housing.

Install the new speed sensor by reversing the removal process. Loosely secure the sensor and sensor harness connection in place, taking precaution to keep the harness from twisting or bending. Once in place, torque the sensor mounting bolt to 16 foot pounds (22 Nm). Tighten any bracket bolts to 84 inch pounds (10 Nm).

Lower the vehicle safely and reconnect the negative battery cable. Refer to your owner's manual to perform an ABS system check to confirm that you installed the sensor properly.

The speed sensor is located out on the transmission extension housing (tail housing), and there can be two different types of sensors used.

Here are some images both 2-WD and 4-WD to help assist you, and let my know if you require any further assistance.


Speed Sensors.







2 Wheel Drive Transmission.

4X4 Transmission and Transfer Case.

1991 Honda Accord 2.2L FI 4cyl the Vehicle Speed Sensor is located mounted on transmission.

Hope help with this (remember rated this help).

CAMSHAFT POSITION SENSOR IS LOCATED BANK 1 ON BACK TOP ENGINE HEAD. YOU ALSO ANOTHER CAMSHAFT POSITION SENSOR ON BANK 2 ON TOP FRONT OF ENGINE.YOUR PURGE SOLENOID VALVE IS ON BANK 2 ON TOP ENGINE HEAD CLOSE TO CMP SENSOR ON BANK 2 ALSO.

The speed sensor is on the tailshaft of the transmission,on the passenger side of the car,it has 3 wires. The output sensors are located on the front of the transmission about mid-way up the housing & only have 2 wires. Note the output sensors are not responsible for vehicle speed. Only the output shaft speed is recorded. They are for finding the correct cvi(clutch volume index) only. If you have a cvi issue,the transmission is toast.

Its probably your speed sensor mounted on the back side of your transmission on top of the final drive gear. Its the sensor/plug located just under the shift linkage. Make sure its bolted down tight and check for any loose connections.

Your car has the 4L60E trans,and the speed sensor is located in the tailshaft of the trans.The tailshaft is located on the rear of the trans,and is held onto the trans with 4,15mm bolts.The driveshaft slips into the tailshaft.The speed sensor will have at least 2 wires going to it.The speed sensor will be located either on the driverside or passenger side of the trans.95 was a transitional year,so the speed sensor could have been mounted on either side.Good luck