Question about Cars & Trucks

Open Question

How to replace Lg gr-p197wvs light bulb

Do not know how to replace cover to replace light globe

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: stop light globes

Remove the little scewy looking things that have plus signs on them. Please dont hesitate to ask for further help if you need it.good luck Buddy!

Posted on Jun 19, 2008

  • 87 Answers

SOURCE: how do you remove the cover on the head light

The cover/lens is not designed to come off. You can try putting the entire light assembly in an oven on low heat for a few minutes, that may soften the adhesive enough to allow the lens to be pried off. There are kits available from auto parts stores to restore the lens.

Posted on Dec 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change light bulb in a 1997 Subaru impreza


Remove cover at back of light ,remove wire clip that hold the globe in then remove globe and replace .

Nov 01, 2014 | 1997 Subaru Impreza

1 Answer

Replace park bulb.vt commodore


To replace the front parklight globe on a vt commodore can be a little tricky.

1.turn the lights on to see which 1 is inoperative once you know turn lights off.
2.open bonnet
3.go to side that is inoperative and on the back of the headlight you will see a round large plastic cover turn this to release it.
4.under the headlight globe there will be 2 wires flow these to the park globe socket gently twist and pull it out.
5.once the sockets out and you can see the globe ,pull the globe out of socket.
6.push new globe into socket
7.refit the socket in headlight
8.refit all trims
9.turn lights on make sure new globe is work..

Jan 22, 2014 | Cars & Trucks

1 Answer

How to replace headlight bulb in 1987 toyota camra


For an 87 specifically, I don't know the answer, sorry. There were at least 3 designs used in the 93-94 models alone. If it is anything like them, you have to either

- press in the plastic barb clip on the centre of the wiring connector at the back of the globe housing, and pull down on the wiring connector to disconnect it. Then rotate the globe holder anticlockwise and withdraw it. Don't touch the new globe glass with your fingers, or if you have, clean it well with metho. Then installation is in reverse. Or for a different design,

- alternatively, unplug the electrical connector. Then turn the hard plastic cover, at the back of the headlight globe holder, anticlockwise and remove it. Then remove the rubber cover underneath. If you are replacing an outer bulb remove the bulb spring clip, first taking note of how it is fitted. On an inner globe there may be a covering socket over the globe itself. Remove that, and the spring clip underneath. Replace the globe. Installation is in reverse, making sure all bits are in position, and the 'lock' mark on the hard plastic cover is facing upwards.

Nov 16, 2011 | Toyota Camry Cars & Trucks

1 Answer

Tail light is burned out on tail light. I have the bulbs but can't figure out how to remove and replace burned out light.


  1. Check with your local auto parts store or look in your owner's manual to find the proper model number of the replacement tail light globe.

  2. Open your trunk or lift your hatchback. Find the cover just on the inside of your vehicle next to the burnt-out bulb.

  3. Turn the two latches counterclockwise to open them so the cover may be removed. In most cases you can turn the latches with your fingers; in some cases you may need a coin or a slot screwdriver to turn them. Remove the cover.

  4. Press the tabs that allow you to remove the tray that holds the tail light globes. There are four tabs on most VW models. Each tab must be depressed to release the tray. Pull the tray out a few inches, as far as the wiring allows.

  5. Press down slightly on the burned-out globe and turn it counterclockwise with your thumb and fingers. It should release easily and then pull straight out. Push the replacement bulb in and turn it clockwise until it locks in place.

  6. Snap the tail light tray back in place. The tray should simply push back into place and the four tabs should "snap" into their locked position. Replace the door cover and turn the door locks clockwise. Test your bulb to see that it is working.

Good Luck

Nov 20, 2010 | 2004 Volkswagen Beetle

1 Answer

How to replace headlight bulb in BA FORD UTE


Rotten job to do. Depending on which side, removal of battery is needed (if so, radio pin code would need be re-entered) Once access is clear, remove electric plug from back of light, remove rubber dust cover and then depress wire globe retainer clip (and flip it on it's hinge)to enable globe be removed.

Oct 31, 2010 | 2003 Ford Freestyle

1 Answer

How to replace the headlight bulb or fuse .how do you take out the bulb or f;ilament when headlight stops working


1.Find The Cover Of The Lamp In The Engine Bay.
2.Remove The Round Cover Turning It Left To Unscrew
3.Remove Base Holding Light
4.Take Out Light From Base Usually By Turning It Or Pushing It Out Of Its Clip
5.Replace Globe (Be Sure Not To Touch Globe With Dirty Hand's)
6. Reassemble Light

Mar 14, 2010 | 2004 Pontiac Grand Am

1 Answer

Changing the brake light bulbs


Have you had a look from inside your boot? I could imagine its covered over with carpet but if you take off the boot wall/carpet and feel around you should find the wires which come out of the rear of the Lens which house the globes. Then you usually twist anti clock slightly (not a screw) to remove globe holder which has globe in it. Or there can sometimes be a wire spring holding the globe holder into the back of the lens. Im pretty sure it takes a bayonetglobe 5W. 47207.

Feb 09, 2010 | 2002 Audi A4

1 Answer

Headlamp Bulb not working on 2003 Cadillac Deville


if its just the one you probably need to replace it by getting to the back of the light to get to the globe,there will be a cover you can remove to do it,if you sometimes slap the light on the lens the globe may come back on indicating a loose filament ....will still need changing though

Oct 27, 2009 | 2003 Cadillac Deville

1 Answer

License plate bulb replacement 2008 Hyundai accent


go to license plate look above it and you will see the globe or globes remove cover and replace bulb,can get at garage

Oct 26, 2009 | 2008 Hyundai Accent

2 Answers

How to change globe on headlight ford focus 2005


avatar3.jpg

brian_au no 1 solution is wrong.. globe is under a spring clip cover . remove cover, then unplug, then release retaining spring behind the globe. replacement is just process reversal

Sep 18, 2009 | 2005 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...