Question about Cars & Trucks

Open Question

P2227 trouble code

Engine light on and car in limp mode

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: need to clear fault codes on jaguar x-type 2.5

disconnect the battery for 10 minutes.

Posted on Jul 27, 2008

Ad
  • 202 Answers

SOURCE: EML, Check Engine, Limp Mode

What is limp mode, and it is MiL light( mal function indicator light)it is not EML. Please specify so i can help

Posted on Jul 24, 2009

  • 1 Answer

SOURCE: My Audi A3 2.0 tdi limp mode/turbo overboost

i also have done a diagnostic test and it states a turbo overboost condition and it drives fine locally but loses power on the motorway and struggles to reach 80mph? any suggestions please email me at shiz86@hotmail.co.uk

Posted on Sep 14, 2009

  • 1 Answer

SOURCE: 2004 Mitsubishi Colt 1.1 Engine management light & code P0122

My girlfriends car has just started with the same problem, a limp home from the garage, a sleep over night and als well next day, for a while... I spoke to Mitsubishi and they have told me the TPS (throttle positioning sensor) is on the accelorator pedle assembly. There PN for this is MN125791 and its circa £88 + VAT. After exhausting all other options I may attempt this replacement and will advise the results.

Posted on Apr 13, 2010

  • 630 Answers

SOURCE: Engine system service required. Code P2584, P242F

P242F is excessive ash accumulation in the Diesel Particulate Filter (DPF). Cure is replacement of DPF at £400!

Posted on Jul 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove a p2227 off a 2007 Volvo Xc 90 3.2


code p 2227 refers to Barometric pressure sensor(BARO)---range /performance problem===causes ---wiring---BARO sensor---ECM
to remove the fault , replace the sensor then use a scan tool to reset the ECM

Aug 16, 2017 | Volvo Cars & Trucks

1 Answer

ETC light came on and limp mode now, 2010 Dodge Caliber....just cleaned the throttle body...now ck engine light on and still in limp mode...what can I do?


When you cleaned the throttle body chance you damaged the sensor. Take it to autozone or similar and have computer scanned for codes. The code will give you a starting point. Remember the code only gives the components that are having trouble but the problem could be somewhere else in the circuit

Jun 16, 2017 | Dodge Cars & Trucks

1 Answer

Mechanics advised that gearbox needs replace after diagnostic Of codes . Dash light still on after codes being read , have had ecu replaced 2yrs ago ? What do you think it could be , thanks phil


didnt specify vehicle --generic answer--until repair is made the vehicle will show engine light and have codes --if gearbox is problem for limp mode /until repairs are made or gearbox replaced you will be in limp mode --and as to sensor find out what one it was --start problem may show back up if sensor was problem --and GET a 3rd opinion you have 2 mechanics with different opinions on your problem and i guess they are reading your trouble codes differently

Sep 20, 2016 | Cars & Trucks

1 Answer

Check engine and service traction control light on in 3rd limp mode


Check engine light on , check DTC'S - diagnostic trouble codes ! Check Engine Light On If not familiar with this take it to a ASE certified repair shop or dealer . 3rd limp mode ? Do you have a message in the DIC - driver information center , reduced power mode ?
ENGINE POWER IS REDUCED
Engine Control Module Description for the 4.8L, 5.3L, 6.0L and 6.2L engine

Apr 16, 2016 | 2008 Hummer H2

1 Answer

Car has gone into limp mode with both codes reading. P0457 and P0137. I have already done a smoke test to see if there were any leeks and we could not find any. any help would be appreciated.


P0131 and P0137 - OBD-II Trouble Codes - RepairPal

repairpal.com > ... > P0131 and P0137 - OBD-II Trouble Codes
Definition of error code P0131 and P0137 - 02 Sensor Low Voltage (Bank I ... Decrease in fuel Eeconomy because PCM is in a "limp home" mode; Engine dies .... The AAmco company replaced 2 oxygen sensors in my car and the engine light ...

Sep 25, 2015 | Cars & Trucks

1 Answer

1993 hyundai sonata has check engine light on and is stuck in limp mode and wont shift out of second gear


the .pcm puts it in limp mode and it will stay in mode until light is turned off. You need to get the trouble code, repair it, erase the codes (with a scanner that retrieves the codes), and then you will be out of limp home mode.

Mar 23, 2014 | 2001 Hyundai Sonata

1 Answer

How to reset limp in mode when there is no trouble codes and no check engine light 1990 dodge dakoda 3.9 L


Try putting the ignition key to on position then disconnect the negative he key still on reconnect the battery, this may re-boot the system....Good-luck....

Jan 04, 2013 | Dodge Dakota Cars & Trucks

1 Answer

Limp mode


If the check engine light is on, you need to get the computer scanned to find out what the trouble codes are.

Jul 20, 2012 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

1996 dodge avenger when cold, the transmission go in limp mode


Is the vehicle's Check Engine Light on? It should briefly light up when you turn the key on (before you start the engine) to show that the light is working correctly. Based on what I've read I believe you should have one or more trouble codes. A place like AutoZone will read the trouble codes for you for free, and you can look them up here - http://www.engine-light-help.com/generic-check-engine-light-codes.html

Dec 12, 2008 | 1998 Dodge Avenger

1 Answer

CEL Error Code p2227


P2227 is thrown for barometric pressure circuit range/performance error. I'm researching what causes it since I have the same thing on my turbocharged Accord.

Aug 26, 2008 | 2007 Honda Civic GX NGV Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...