Question about Cars & Trucks

Open Question

I just installed a used fisher V-plow on my dodge 2500. It came off a chevy. I have a power light on the controller but the plow will not do anything. The selonide has 12 volts on both sides of the little post but it will not transfer power over to the other side. If jumper power across the selonide to engagethe pump motor to get to the pump to run the plow will still not do anything.I

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2004 Dodge Dakota

Replace your resistor if you haven't already. I had the same issue with mine, it only worked on high.

Posted on Dec 30, 2008

Ad
  • 51 Answers

SOURCE: minute mount 2 fisher plow stopped working up down

there could be a flat spot in the motor that runs the blade

Posted on Mar 03, 2009

wracefans24
  • 1985 Answers

SOURCE: 1997 Dodge Ram 2500 brake lights do not work. The

you need to do basics first,
check to see if bulbs are good,then verify no voltage at bulbs,
check to see if your truck has has a tailor hitch and wiring installed.
where they connect to your original wire is where you need to check first,

Posted on Nov 22, 2009

  • 1 Answer

SOURCE: 2001 dodge 2500 diesel oil leak in front of power

The power steering pump is piggie backed to the vacuum pump. The seal in the back of the vacuum pump has engin oil under presure behind it cousing a leak that gets worse over time. Cummins make a seal kit to fix this leak.

Posted on Feb 05, 2010

oldmanewtoys
  • 414 Answers

SOURCE: my fisher plow wont move

Sounds like pump is not working, check all fuild lines. Unless the plow is all electric, then the ground

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I chang fues still no power fisher minit plow 2005 gmc plow work fine last year put on now no power to control box


May want to begin tracing the wiring harness from the plow all the way to the control box.

Dec 23, 2016 | GMC Cars & Trucks

1 Answer

Beast way to wire up plow lights on a 2008 dodge Dakota sxt 3.7 v6 4x4


Trying To Wire Plow Lights Without A Harness - Snow Plow Forum ...

www.snowplowforums.com/...lighting-wiring/13714-trying-wire-plow-li...

Oct 11, 2006 - 25 posts - ‎8 authors
They both work when I hook up the battery charger to them. ... This way,the plow lights only come on when the plow is plugged in,and ... A relay equivalent to Napa part #AR272 is good, if you give the number at Advance or Autozone they can cross reference it. 92 Dodge Dakota - 7'6" Snoway MT with DP ...Missing: 2008

Meyer Snowplow Install - Part 2 (Electrical) - YouTube

? 10:01
https://www.youtube.com/watch?v=5RSFqO80cLM
May 20, 2009 - Uploaded by CentralPartsWarehse
A real plow install taking place in our on-site, full service shop. In this video we'll show a complete snowplow install taking place on a 2009 ... How much does a complete set up like this cost? ...BEST SNOW PLOWING VIDEO!

Light Wiring for Meyer Plow - DODGE RAM FORUM - Ram Forum



Dec 13, 2015 | Dodge Cars & Trucks

1 Answer

Fisher minute mount plow


does the pressure release close to raise the plow?

Jan 05, 2014 | Dodge Cars & Trucks

2 Answers

Lights on a fisher xtreme plow wont work


I'm guessing that you have already checked to make sure there is power going to the plow lights. If not use a test light and make sure. The most likely problem is the grounds from the plow lights themselves to the frame. Take the lights apart and check and/or replace the grounds, wires inside the case take a lot of vibration and that can cause them to fail.Don't forget to check the bulbs to be sure they're good too. Hope this helps.

Dec 17, 2009 | 2007 GMC Sierra 2500HD

1 Answer

Hi, I have a 2000 dodge ram and when i plug my fisher plow up only one light works on the plow and one on the truck .when the plow is un hooked from the truck all the truck lighs work,and when i hook up...


There is a ground that is deteriorated in the harness. trace the ground lead back from the connection to your truck. Once you find the break, that should take care of your problem.

It is also possible to be a power lead, so check them also, but more often than not it is a ground.l

Hope this helps.

Dec 14, 2009 | 2001 Dodge Ram 2500 Truck

3 Answers

I have a fisher minute mount and one headlight dim


A poor ground. Check the ground wire inside the light housing itself and then make sure it is getting a good ground where it mounts to the plow frame. Hope this helps.

Dec 05, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...