Question about Nissan Pickup

Open Question

Z16 3895 10

What is the head bolt tightening sequence fo a z16 please?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tneubauer
  • 437 Answers

SOURCE: torque and tightening sequence for 1999 2.2 chev

Cylinder Head Bolts

Step 1
Head Bolts A 46 (62)
Head Bolts B 43 (58)

Step 2 Additional 90 Degrees

Tightening Sequence:
http://www.anubiscycle.com/fixya/99cavheadsquence.png

Posted on Jan 17, 2010

Ad
tburtk
  • 158 Answers

SOURCE: torque on 3.0 ford taurus head bolts

40 ftlbs then 73 ftlbs then recheck at 73 ftlbs

Posted on Feb 06, 2010

  • 14 Answers

SOURCE: 1998 FORD FESTIVA HEAD BOLT

1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L
Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

Posted on Aug 06, 2010

iambanshee74
  • 3489 Answers

SOURCE: want to know the amount of torque pressure do i

To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Posted on Dec 16, 2010

emissionwiz
  • 76691 Answers

SOURCE: cylinder head tightening sequence for ford mondeo 1.8i zetec petrol

Go to this LINK for the info in pdf format, the sequence is on page 16 of the pdf file.

Posted on Feb 16, 2012

Testimonial: "Great help...just the info I needed to do job. Thankyou very much."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings on a fiat strada 1.6 16v elx 2005 model for head and cams please


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jun 03, 2016 | Fiat Cars & Trucks

1 Answer

What is the cylinder head tighten torque


Have a look on this link. You may be able to find your car:

SPECIFICATION LOOKUPS

Cylinder head bolts are usually tightened to around 65 ft-lbs, depending on what the car is.

There's more than 4 cylinder head bolts... There's usually 10 bolts.
There's also a sequence for tightening the bolts:

cylinder head tightening order Google Search

When tightening cylinder head bolts do it in 'stages' and follow the sequence .. ie.. tighten the bolts finger tight first, then torque them up to about 25 ft-lbs. Wait 2 minutes.

Then tighten them to about 45 ft-lbs in sequence. Wait 2 minutes.

Do it again up to about 55 ft-lbs. Wait 2 minutes.

Tighten them up to 65 ft-lbs or whatever is recommended for your car.

Tightening in order/sequence pulls the cylinder head evenly onto the block. Waiting 2 minutes between stages allows a 'stretched' bolt to 'settle'.

Feb 17, 2016 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

Need torque specs and bolt pattern for 96-2003 cavalar head gasket please send to mike@rstorage.net


zjlimited_890.jpg

Fig. 7: Location of the cylinder head retaining bolt holes





zjlimited_891.jpg



Fig. 13: Cylinder head bolt torque sequence for 2.2L engines

Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm) plue 90 degrees.

Hope helps.

Mar 18, 2011 | Chevrolet Cavalier Cars & Trucks

3 Answers

How do I remove the head? (Blown Head gasket)


prev.gif next.gif Cylinder Head REMOVAL & INSTALLATION 2.3L Engine
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable, then drain cooling system into a suitable container.
  3. Detach the heater inlet and throttle body heater hoses from water outlet. If accessible at this time, disconnect the upper radiator hose from the water outlet.
  4. Remove the exhaust manifold. For details, please refer to the procedure located in this section.
  5. Remove the intake (camshaft housing for SOHC) and exhaust (DOHC only) camshaft housings.
  6. Unfasten the oil fill tube bolt/screw then remove the oil fill cap and level indicator assembly. Pull the oil fill tube upward to unseat from block.
  7. Label and disengage the injector harness electrical connector.
  8. Detach the throttle body-to-air intake duct.
  9. Tag and disconnect the power brake vacuum hose from the throttle body.
  10. Remove the throttle cable bracket.
  11. Remove the throttle body from the intake manifold with the electrical harness and throttle cable attached and position the assembly aside.
  12. Tag and disconnect the MAP sensor vacuum hose from the intake manifold, then remove the intake manifold brace.
  13. Detach the electrical connectors from the MAP sensor, IAT sensor and the EVAP canister purge solenoid.
  14. If not already done, detach the upper (inlet) radiator hose from the water outlet.
  15. Disengage the coolant temperature sensor connector(s).
  16. Unfasten the cylinder head bolts in reverse order of the installation sequence shown in the accompanying figures.
  17. Lift the cylinder head from the engine block. Remove and discard the gasket. Inspect the oil flow check valve for freedom of movement.
  18. Using a suitable solvent, thoroughly clean and dry all bolts, bolt holes and mating surfaces. Inspect the head bolts for any damage and replace, if necessary. If using a scraper to clean the old gasket material from the mating surfaces, use only a plastic or wood one, NOT a metal scraper. Do NOT allow any debris to fall into the engine! To install:
  19. Place a new cylinder head gasket on the cylinder block, then carefully position the cylinder head in place.
  20. Sparingly coat the head bolt threads with clean engine oil, then allow the oil to drain off before installing.
  21. On 1988-89 engines, install and tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 80°and the long bolts an additional 90°in sequence Fig. 5: Cylinder head bolt tightening sequence - 1988-89 2.3L engine 86883121.gif
  22. On 1990-91 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 100°and the long bolts an additional 110°in sequence Fig. 6: Cylinder head bolt tightening sequence - 1990-91 2.3L engine 86883122.gif
  23. On 1992 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten, in sequence, head bolts 1-6 to 26 ft. lbs. (35 Nm), 7-8 to 15 ft. lbs. (20 Nm) and 9-10 to 22 ft. lbs. (30 Nm).
    • Step 2 - Tighten all head bolts, in sequence, an additional 90°using J 36660 or equivalent
    • Step 3 - In sequence, loosen each bolt one turn, then immediately re-tighten to the specified torque
    • Step 4 - After completing step 3 on all 10 bolts, tighten each bolt, in sequence, an additional 90° Fig. 7: Cylinder head bolt tightening sequence - 1992 2.3L engine 86883123.gif
  24. On 1993-95 vehicles, tighten the cylinder head bolts to the specifications shown in the accompanying figures. Fig. 8: Cylinder head bolt tightening sequence and specifications - 1993 2.3L engine 86883124.gif
    Fig. 9: Cylinder head bolt tightening sequence and specifications - 1994-95 2.3L engine 86883125.gif
  25. Engage the coolant temperature sensor electrical connector(s).
  26. Connect the upper radiator hose to the water outlet.
  27. Install the intake manifold bracket.
  28. Attach the following electrical connections: MAP sensor, IAT sensor, and the purge solenoid.
  29. Using a new gasket, install the throttle body to the intake manifold.
  30. Install the accelerator control cable bracket.
  31. Connect the throttle body-to-air intake duct.
  32. Install the oil fill tube and level indicator.
  33. Install the camshaft housing(s).
  34. Install the exhaust manifold. For details, please refer to the procedure located in this section.
  35. Connect the heater inlet and throttle body heater hoses to the water outlet.
  36. Fill all fluids to their proper levels.
  37. Connect the battery cable, start the engine and check for leaks.

Sep 24, 2010 | 1992 Oldsmobile Achieva

1 Answer

Whats the bolt pattern for my 1995 ford escort head?


1.8 liter..NOTE: Lubricate the cylinder head bolts using the specified engine oil.

Install the cylinder head bolts. Tighten the cylinder head bolts in 2 or 3 steps in the sequence shown to 76-81 Nm (56-60 lb-ft).

b064be7.gif
1.9 liter
Apply a light coating of engine oil to the threads of the new cylinder head bolts. Install the new cylinder head bolts to the cylinder head. Following the sequence shown below, tighten the cylinder head bolts to 40-60 Nm (30-44 lb-ft). Loosen all cylinder head bolts approximately two turns, then retighten the cylinder head bolts to 60 Nm (44 lb-ft) following the sequence shown. After tightening, turn all bolts 90 degrees, in the same sequence. Complete bolt tightening by turning them an additional 90 degrees, in the same sequence. 398246b.gif

Aug 21, 2010 | 1995 Ford Escort

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

What is the cylinder head torque on a 2001 jeep cherokee


Please don't forget to rate....thanks:


e1aba13.gif

  1. Tighten the engine cylinder head bolts in sequence according to the following procedure

    CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  5. Tighten bolts in sequence:
  6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  7. Bolt 11 to 100 ft. lbs. (135 Nm).
  8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  9. Check all bolts in sequence to verify the correct torque.

Mar 06, 2010 | 2001 Jeep Cherokee

1 Answer

What are the torque settings for the cylinder head 2000 subaru forester


This procedure is for the SOHC only.

E: INSTALLATION
1. CYLINDER HEAD

  1. Install cylinder head and gaskets on cylinder block. CAUTION: Use new cylinder head gaskets.
  2. Tighten cylinder head bolts.
  1. Apply a coat of engine oil to washers and bolt threads.
  2. Tighten all bolts to 29 Nm (3.0 kg-m, 22 ft. lbs.) in alphabetical sequence. Then tighten all bolts to 69 Nm (7.0 kg-m, 51 ft. lbs.) in alphabetical sequence.
  3. Back off all bolts by 180° first; back them off by 180° again.
  4. Tighten bolts (a) and (b) to 34 Nm (3.5 kg-m, 25 ft. lbs.) .
  5. Tighten bolts (c), (d), (e) and (f) to 15 Nm (1.5 kg-m, 11 ft. lbs.) .
  6. Tighten all bolts by 80 to 90° in alphabetical sequence. CAUTION: Do not tighten bolts more than 90°.



  1. Further tighten all bolts by 80 to 90° in alphabetical sequence shown in figure provided. CAUTION: Ensure that the total "re-tightening angle" [in the former two steps], do not exceed 180°.

May 24, 2008 | 2000 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...