Question about 1988 Toyota Camry

Open Question

How to 1988 toyota camry alternator belt tension

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: toyota echo serpentine belt

The only way to loosen and tighten the serpentine belt is by loosening the alternator and sliding it back or forward. There are TWO bolts that must be loosened, one above, and one below the alternator pulley. A bit of penetrating oil can make things easier.

Posted on Jan 09, 2009

  • 21 Answers

SOURCE: I need to change the belt on 2003 Toyota Camry.

you should have a belt diagram on the front cross member of the vehicle under the hood that tells you how to do the job need

Posted on Apr 04, 2009

  • 1861 Answers

SOURCE: power steering belt on 1991 toyota camry

Locate the idler pulley. Loosen the nut in the center of the idler pulley. Then loosen the bolt that protrudes from the back of the pulley. This will let the belt go slack.

Posted on Jul 18, 2009

projdoc
  • 2236 Answers

SOURCE: replace alternator belt only for 1993 toyota camry

loosen the mounting bolts on the alternator, remove the old belt, replace with the new belt, slightly tighten the top mounting bolt, pull the alternator up until the belt is tight or if there is an adjustment bolt, crank down until tight (shouldn't bow more than 1"), and tigten other hardware.

Posted on Aug 12, 2009

dvdeater
  • 372 Answers

SOURCE: replacing the serpentine belt on a 2003 toyota

there is a 19mm tensioner attached to the bracket put socket and long breaker bar and standing at front of car pull toward you to release tension

Posted on Aug 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HDo I remove and install an idler pulley on a 2005 Toyota Camry?


How to replace drive belt tensioner Toyota Camry - YouTube

? 4:26
https://www.youtube.com/watch?v=gfSJvN-CE2E
Feb 22, 2013 - Uploaded by Fix It Angel
2002 2003 2004 2005 2006 2007 2008 2009 Toyota Camry. Engine, 4 cylinder, 2.4L, 2AZ-FE. 2004 Toyota ...

Idler Pulley, How to replace (EASY and CHEAP) - YouTube

? 4:56
https://www.youtube.com/watch?v=axAltpW8wR4
Nov 2, 2013 - Uploaded by ChrisFix
Idler pulley squeak? Learn how to fix a squeaky pulley in your car. The serpentine belt in your car powers the ...

2007 Camry Serpentine Belt Replace - 4 Cyl, 2.4 liter ...

? 4:21
https://www.youtube.com/watch?v=ejhyCrh96a8
Jan 13, 2013 - Uploaded by Flyin Brian
I show you step-by step how to get the old belt off and install a new ... ... Water pump replacement 2007 Toyota ...


Jan 27, 2016 | Toyota Cars & Trucks

1 Answer

How do you remove the Alternator on a 2008 Toyota Camry V6 LE?


Undo the tensioner or release the belt ,disconnect the battery undo the bolts holding the alternator take note on how the belt is fitted up to all pullies ,write a diagram so you don't forget,remove alternator.

Oct 10, 2015 | Toyota Cars & Trucks

1 Answer

1988 Toyota Camry LE clicking noise during acceleration


start with premium gas or injector cleaner, could be a low octane ping. this may be hard to diagnose with out hearing the noise so the other thing i would have you do is remove the belts and run the engine. sometimes when a bearing in an alternator, idler pulley, a/c compressor or belt tensioner goes bad they can make a clicking noise. try to listen if the noise is coming from the belt area, the transmission area or some other spot. spin all the pulleys with the engine off and wiggle them to see if any are bad

Mar 31, 2014 | 1988 Toyota Camry

1 Answer

1988 toyota pickup 22re alternator heating up


Check all other accesories that are driven by the same belt. One of them has a bad bearing that is causing the belt to heat up

Mar 16, 2010 | 1988 Toyota Pickup

1 Answer

How to replace timing belt on 2000 toyota camery 4 cy


disassemble the protection parts from the motor. Then release the tension of the old belt by unscrewing a little the alternator bolts. take out the old belt and fix the new belt with the marks on it over the marks on the wheels. tension the belt with the alternator and screw back the bolts and the protection parts.

Mar 12, 2010 | 2000 Toyota Camry

1 Answer

I had 2003 Toyota Camry 4 cylinder in for


While it is a possibility, having the tensioner lose tension seems more probable that it locking up as the mechanics have stated. You seem to know what you are talking about, so why not try throwing a wrench on it and turning it towards the serpentine belt? Then you can see for yourself if it has seized or not. It is the small pulley that doesn't seem to power anything like your AC compressor, alternator, fan, crank, powr streering. match a wrench to the size of the bolt and turn it, if it moves take the belt off (noting how it goes) and put the new one on saving you 280 dollars.

Dec 04, 2009 | 2003 Toyota Camry

1 Answer

Do you have any inf on refitting timing belt on a toyota camry sv21 1.8 petrol engine thank you.


the only thing that might work is there is a tension bar on one of the pullys you can try to tighten it not replace it

Jul 08, 2009 | 1988 Toyota Camry

1 Answer

Engine light


You need to Check the Belt Tension,Belt Tensioner, Battery and the Alternator. If the Belt is even a Little Loose it will not allow the Alternator to Charge the Battery fully.

Jan 25, 2009 | 2002 Toyota Camry

1 Answer

Where is the serpintine belt tensioner on a 2003 Toyota Canmry (4cylc)


its in between there you need a 19mm and a long breaker bar you will see it its really uncomfortable...

Oct 18, 2008 | 2003 Toyota Camry

Not finding what you are looking for?
1988 Toyota Camry Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...