Question about 1997 Chevrolet S-10 Pickup

1 Answer

Brake problem we replaced the entire brake system, rear wheel cylinders (2), shoes and drums. front calipers (2), turned rotors and replaced inner and outer wheel bearings and seal.new master cylinder and power booster unit. we bled the brakes with no problems....the peddle was nice and firm, all seemed well until we started the truck, stepped on the brake peddle, and it went to the floor. maybe the last inch of peddle, before hitting the floor, had a little brake pressure. we turned the truck off, hit the peddle and all was fine...do I have a abs problem, or did I miss something. I thought I would have a new system, but ????? any tips or advice would be great! aloha, unk' larry

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 40,691 Answers

Try adjusting the rear brakes up correctly
the spring that holds the shoes together pushes all the brake fluid back into the reservoir and each application has to move the shoes back into contact with the drum
that is enough to get the pedal close to the floor

Posted on Apr 01, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Brakes no longer work in 1989 Chevy half ton pickup 2 wheel drive 350cubic inch

change dump valve under master cylinder

Posted on Aug 17, 2008

Jay_from_Ma
  • 99 Answers

SOURCE: 1998 chevy C-1500 brake problems

Try a clean and adjust on the rear shoes, because sometimes when they aren't properly adjusted they won't seem to work properly. Also there is a common "squishy" petal feeling after brake work on most all larger GM's around that year, wich I have run into several times. Try test driving it, and put a couple miles on it, That usualy helps.
Good luck!

Posted on Dec 17, 2008

emissionwiz
  • 75005 Answers

SOURCE: brake pedal dropping to floor

do u have the antilock brake bleeding tool? if not you will need to have the dealer bleed the brakes, the ABS control valve must be electricaly held open to bleed the brakes there of course is a special tool for this.

Posted on Oct 18, 2009

Testimonial: "Thank You"

  • 19 Answers

SOURCE: Spongy brake pedal even after ABS bleed and base brake bleed.

Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Posted on Dec 19, 2009

xdmann
  • 43 Answers

SOURCE: 1999 Chevy Tahoe- Soft Brake Pedal

Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver's side front brake became suddenly stuck ( and mildly smoking) on my 1991 ford aerostar xl that has been excellently maintained. The 'Rear Anti-Lock' brake light came on yesterday and stayed on, and...


yes baby it to him and replace both calipers and rotors as they will work better with your new brake pads. Do Not Do a half a job when it comes to brakes. its your family you are dealing with. calipers are cheap rotors are cheaper and pads are also cheap. its 3 hours labour to do a complete front brake job and rear brakes take 2 hours. with new shoes turn drums replace wheel cylinders and new rear brake hardware price in Canadian for front brakes under 400 price for rear under 250 American parts prices slightly different but labour times the same

Sep 18, 2013 | Ford Aerostar Cars & Trucks

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

Help with installing brake shoes on 1993 buick park ave


Your Buick has front disc brakes...and rear drum brakes...the usual concern is the front pads as they are used more...these are the easiest pads to replace...as you only need to remove the caliper from the rotor with 2 bolts to lift off...Be sure to push the piston all the way back into the caliper to install new pads...rotors are pop offs too...The rear drum is different...the brake shoes are held on with clips and springs...try keeping one of the shoe assemblies intact while you switch out the other shoes...be sure to inspect the rear wheel brake cylinders for possible leaking...usually an oil build up inside the brake drum...these are inexpensive and should be switched out on a 93 Buick...:) Hope this helps.

Apr 02, 2011 | 1993 Buick Park Avenue

1 Answer

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before...


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Feb 23, 2011 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

3 Answers

1999 Chevy tahoe 2dr Brake shudder intermitant hard pedal.


You probably need to surface the rotors and the drums. I have gotten brand new rotors that were so warped that they were below min. thickness (not kidding) after surfacing them. Needless to say, they went back to the parts store. So now I surface every new rotor that I install. Happens to rotors way more than drums, but have hade a couple of drums that were warped when new so I check them before installing them. Good luck. Hope this helps.

Jun 29, 2009 | 1999 Chevrolet Tahoe

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

94 landcruiser brakes


Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.


  1. Raise and support rear of vehicle, then remove wheel and tire assembly.
  2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
  3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
    1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
    2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
    3. On 2WD T100 models, proceed as follows:
      1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
      2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
    1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
    2. Remove adjusting lever spring, then the adjuster from front shoe.
    Inspection
    1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      1. On 2WD T100 models, proceed as follows:
        1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
        2. Assemble and install wheel cylinder.
        3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
        1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
            1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
            2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
            3. Install tension spring.
          1. Ensure proper parking brake travel.
          2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
          3. Adjust strut to shortest possible length, then install drum.
          4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS
  1. Remove caliper.
  2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
  3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
  4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
  5. Remove free wheel hub body and gasket.
  6. Remove locknut, lock washer and adjusting nut.
  7. Remove axle hub and brake disc as an assembly.
  8. Remove oil seal and inner bearing from hub.
  9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.
  1. Raise and support front of vehicle, then remove tire and wheel assembly.
  2. Remove clip and hole pins, Fig. 9.
  3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
  4. Lubricate caliper housing with suitable brake grease at pad contact points.
  5. Reverse procedure to install.

Jan 28, 2009 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...