Question about 2007 Chevrolet HHR
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
First check alt At The Back of Alt Big Red Wire Were hooks to Post (stud) Do you have voltage ?? How Much??
What Voltage do you have at same Place with Engine Running ??
Now At wires Were they plug into Alt ,Top. Wires in White Plastic Clip, Do You Have Powe With Key On ?? How Much Voltage??
Jump across the 2 in the clip (with Engine Running)ONLY TEMPORARY!! Do You Have Voltage at Battery ?? How Much??
If Over 13volts With Clip On (Jumped) You Need A Internal Voltage Regulator ..
Is Batt Light On on Dash ??? Theres A Lot Of Testing You Can Do !!! And I will Need More Infomation to Keep Going ... These are just some Possible Problems No Way In Depth ...
Could Be a Number of things Or May be Just as Simple As a Blown Fuse, Dirty Batt Cables ETC etc etc I Hope It Puts You On The Right track !!!!!!!!!!
Posted on Jan 07, 2009
Check all your fuses if you had a system failure it could have blown a fuse. I am not sure on your vehicle where the fuse is in the car or under the hood it could also have a relay. You can check your alternator by checking the voltage at the back of the alternator where the big wire bolts on. You should have 14+ volts at the alternator.
Posted on May 24, 2009
Ok, i understand that you have replaced the alternator, but there seems to be a non charge state in this case. i recommend checking the charging system. use the procedure below to isolate this issue.
Wear protective eye wear and clothing and remove all jewelry when checking your battery and charging system. Jewelry is a good conductor of electricity and is not recommended. Most batteries wear out every 3 to 5 years and need to be replaced. Always replace your battery with an equal replacement battery to assure proper operation. Automotive batteries have a +positive terminal (red), - negative terminal (black). The battery in this illustration has a protective cover over the positive terminal to prevent short circuit in case of an accident. Electricity is stored in the battery and then supplied to the vehicle when the engine is not running. While the engine is running the vehicles alternator charges the battery for future use. (Note: never disconnect the battery while the engine is running. If the battery cable is disconnected from the battery a spark can be generated which can cause the battery to explode or a major electrical malfunction to occur.)
To check a battery surface voltage, remove the positive terminal protective cover. Connect the +positive side meter lead (red) to the positive side battery terminal. Connect the - negative (black) side meter lead to the negative battery terminal. With the vehicle not running and the car sitting over night the battery voltage should be between 12.5 and 12.8 volts.(You will need to use a voltmeter for this testing procedure)
The alternator is rotated by a drive belt driven by the vehicles engine while it is running. Electrical voltage and amperage are generated to recharge the battery and supply voltage to the electrical system of the car. The alternator is held in place with mounting bolts. There is a main electrical wire on the rear of the alternator that supplies voltage to a main voltage junction box. If your alternator is not charging properly, your battery will slowly drain down from operating all the electrical systems in your car and stop the car from running.(most non charge states will be the cause of a loose belt or a low tension rate, due to a mis-adjusted alternator. make sure you have enough tension in the belt for full rotation of the alt pulley)
Next, you will need to check the alternators output with the Amp meter.
Testing the amperage output of the alternator is good for measuring the amount (not the level) of voltage the alternator can produce. This test can be tricky because if the alternator is weak it can still show it as producing amperage. Which is good, but if the voltage is low, it will still allow the battery to go dead. To check the amperage output of an alternator an amp meter is needed. Once the meter is connected start the engine. Next turn on all electrical accessories and raise the engine idle to about 1200 RPM. The alternator should output the max amperage it was designed to produce. Example: a 90 amp alternator should output about 88 amps. Note: An alternator cannot sustain maximum output for long periods of time. If the alternator is forced to operate at maximum output it will overheat and fail. An alternator is designed to operate at max amperage output only for a reasonable amount of time.
((Connect the voltage meter lead the same way you would in a battery static voltage check, Start engine (do not drive) at engine idle the voltage should be between 13.6 to 14.3 volts. If not the alternator may need replacing.)))
Posted on Sep 30, 2009
I don't know what kink of car you have, but some will have a alternator fuse, also with a volt meter check voltage on big wire at back of alternator should have 13.5 + volt's, then check voltage at battery should have same voltage there also, do this with car running, if you do not have same voltage at battery less short between alternator and battery or bad fuse. There also some fuse links at starter on some car's.
Posted on Dec 03, 2009
Tips for a great answer:
Jul 06, 2017 | 2007 Nissan Murano SE
Jan 01, 2016 | 2007 Chevrolet Trailblazer
Mar 23, 2015 | 2007 Acura MDX Tech
Jul 15, 2014 | 1989 Ford F 250
Feb 14, 2014 | 2007 Chevrolet HHR
Sep 19, 2012 | 2006 Saturn ION 2
May 24, 2009 | 2007 Chevrolet Uplander
Jul 15, 2008 | Mazda Tribute Cars & Trucks
17 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: