Question about 2005 Chevrolet Cobalt

Open Question

How do I remove the radiator overflow bottle from a 2005 cobalt?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACE RADIATOR 2005 CHYSLER 300C 5.7 HEMI ?


Four bolts hold it onto the support bracket. Remove both radiator hoses and disconnect the electrical connections to the temp sensor and fan sesnor. Take out the 4 bolts and lift up and away. Transfer the sensors from the old radiator to the new one. Do not mix up the locations of the sensors. Re install the radiator, put back the 4 bolts and reconnect both radiator hoses. Fill the radiator with the correct mixture of antifreeze and water for your vehicle. If it won't all go in, start the engine and let it run until the thermostat opens and then finish adding the coolant. Add water to the radiator until water can be seen circulating. Add some water to the overflow container and put the cap on the filler neck. Run a little longer then shut the engine off. When the engine has cooled off check the level in the overflow bottle and add coolant to the mark.

Feb 19, 2015 | Cars & Trucks

1 Answer

Transmission fluid in radiator & running out radiator overflow bottle


The transmission cooler is located inside the radiator on pilots, they are notorious for rotting out and leaking ATF into the radiator and vice versa. This wil quickly lead to your transmission seals failing and destroying your transmission. Happened to my wife's pilot and got Honda to split the bill

Sep 10, 2012 | 2005 Honda Pilot

2 Answers

Where do u put the water in on a colt? Can't find it?


A tank used for storing excess coolant; connected to the cooling system with a small-diameter overflow hose.

The coolant reservoir is the bottle,under the hood, that holds the radiator fluid. it is also known as a overflow bottle. When the car gets hot,the overflow bottle, releases steam to relive the pressure in the radiator. excess coolant is also stored here.

mc1bean_127.jpg


I hope this helps, Mike from fixya.

mc1bean_128.jpg

Aug 07, 2011 | Mitsubishi Colt Cars & Trucks

1 Answer

Need to change coolant recovery tank can a anyone do it


Yes you can do it yourself

Degas Bottle Removal
  1. Drain radiator (8005) until engine coolant is out of degas bottle. Disconnect radiator overflow hose (8075) and engine coolant vent hose at degas bottle.
  1. Remove power steering oil reservoir retaining screws and position power steering oil reservoir (3A697) out of the way.
  1. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
Installation
  1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 lb-in).
  1. Connect degas bottle hose and clamp to degas bottle.
  1. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
  1. Connect radiator overflow hose and engine coolant vent hose to degas bottle.
  1. Fill and bleed engine cooling system as described. Check for coolant leaks and proper engine coolant level after engine reaches normal operating temperature.


    q3699b.gif


    Item Part Number Description 1 8100 Radiator Cap 2 - Nut (1 Req'd) 3 - Bolt and Retainer (1 Req'd) 4 - Nut (1 Req'd) 5 - Bolt (1 Req'd) 6 - Coolant Recovery Hose 7 - Coolant Return Hose 8 - Coolant Recovery Hose 9 8A808 Degas Bottle A - Tighten to 9-12 Nm (80-106 Lb-In)
Hope this helps.

Zeppelinx12

Mar 08, 2011 | 1999 Ford Taurus

2 Answers

Heat is not working - coolant was low so filled it.... problem here... heard something about an air pocket


If you dont have an external coolant leak anywhere under your hood that has shown up on your driveway it could be the intake manifold or the headgasket leaking. Also check the thermostate to solve the heat issue.

Jan 05, 2011 | 1998 Pontiac Bonneville

1 Answer

93 lincoln mark v111 antifreeze radiator, how do i bleed air out of rad, coolant from coolant bottle into radiator?


When you top off the radiator you fill it to the neck where the cap goes. When the engine heats up the antifreeze eventually will distribute and the excess will go into the overflow bottle.

After the car cools, it will draw the antifreeze from the overflow tank into the radiator. Then check the level line on the overflow bottle(tank) for the normal amount of antifreeze per marks on the bottle.

You should have your radiator cap checked for its pressure rating. Use the type of cap which allows for an overflow system. The older caps would not let the antifreeze flow both ways.

Mar 26, 2010 | 1998 Lincoln Mark VIII

1 Answer

I have an antifreeze leak at the piece of hose connected to the radiator cap (2005 Dodge Dakota.) What is the piece called and do you have a picture? I think its called a goose neck?.


it is just the overflow hose,you can replace it with regular vacume hose that diameter,but you should replace the radiator cap,its letting off pressure.the hose connects to your overflow bottle

Jan 10, 2010 | 2005 Dodge Dakota

1 Answer

Remove radiator overflow bottle on 2001 Buick


Often times the bottle is anchored from underneath in the wheel well.

Sep 22, 2009 | 2001 Buick Century

1 Answer

Replace a coolant reservior on a 1999 ford taurus


If you need Illistration I Can Email it to you Im at
rejakwilson @ aol.com

Removal

CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs, the service change interval on Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.

  1. Drain radiator until engine coolant is out of degas bottle. Disconnect radiator overflow hose and engine coolant vent hose at degas bottle.
  2. Remove power steering oil reservoir retaining screws and position power steering oil reservoir out of the way.
  3. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
Installation
  1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 inch lbs.)
  2. Connect degas bottle hose and clamp to degas bottle.
  3. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
  4. Connect radiator overflow hose and engine coolant vent hose to degas bottle.

Aug 28, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
2005 Chevrolet Cobalt Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...