Question about Cars & Trucks

Open Question

03 accent transmission kickdown band adjustment

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76682 Answers

SOURCE: 2002 Ford Explorer with 5R55W transmission: How

I can't find any reference to an adjustment in the overhaul manual, so i will assume this means no adj ness. or provided for.

Posted on Mar 24, 2009

Ad
denanjen05
  • 6 Answers

SOURCE: honda accord kickdown cable adjustment procedure

if u want it to kick down later simply adjust more slack in the cable if u want it to kick down earlier make it tighter check the slack at the throttle body side adjust it to have about 1/4 inch slack drive and adjust acordingly

Posted on Oct 07, 2012

emissionwiz
  • 76682 Answers

SOURCE: how to adjust reverse band on ford fmx transmission

Just google it, there are lots of sites that come up.

Posted on Oct 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Having problems with my Automatic transmission Kickdown, when i press the accelerator pedal all the way down, the gears will not shift, and the gears will not kick down going uphill, i have to manuall


Most cars with automatic transmissions have a kick down switch that is sometimes mounted on the transmission but activated by the throttle linkage. A good mechanic should be able to correct this quite easily.

Apr 23, 2014 | 2010 Hyundai Accent

3 Answers

'03 accent - reverse not engaging- drive wont shift above 30 mph -fluid is fine, battery is fine, brake/stop switch seems ok. cycled tranny thru gears &rechecked fluids & all ok -O/D lock switch...


Seems like your transmission has failed. Either some syncros or bearings are worn out. Its sounds like its time to either have it rebuilt or replaced.

Mar 24, 2011 | 2003 Hyundai Accent

1 Answer

I have a 1997 dodge dakota 4x4 ,it won't shift from 1 st to 2 nd unless i manually shift into neut. and ley the rpm. drop and then back into drive. i've replaced gov. sol., and gov. transducer, and the...


I would check out your kickdown band inside your transmission. You can check it by removing the pan and pulling down the valve body. Once you get the valve body down you can see the kickdown band it is the band closest to the front. Check the tabs where the band adjuster is. The tabs on the band itself can get bent causing the band to be way out of adjustment which will cause shifting problems like you are having. Sometimes you can just bend the tabs back and reset the adjustment on the band. If its too bad though you will have to pull the transmission and change the band. But before you do all this check to make sure your kickdown lever and cable are working properly. Sometimes if it is binding on your shift leaver your shifter might move hard or your gas pedel can feel super easy to push or hard to push. good luck hope this helps

Nov 11, 2010 | 1997 Dodge Dakota

1 Answer

1997 Dodge Caravan Sport. I was driving normal then it quit pulling. Now have 3 forward gears no more than 8 miles an hour. No reverse. Dropped trans pan small metal on magnet.Fluid looked ok. Changed...


The correct fluid to put in a 1997 van is (ATF-3). Sounds like you need to make adjustment on both the forward and reverse bands of the transmission to correct your problem. The kickdown band (front) forward is located at the top (outside) of the transaxle near the front. To adjust the band,loosen the lock nut approximately 5 turns. With the lock nut loose the adjusting screw should turn freely in case. Tighten the adjustment screw with an inch lb. torque wrench to 72 in-lbs. Then back the screw out 2 1/4 turns, hold the screw in place and tighten the lock nut to 35 ft-lbs. Then after removeing the transmission pan and filter the low-reverse band is located next to the valve body. Loosen the lock nut 5 turns so the adjustment screw is free. Turn the adjustment screw in to 41 in-lbs, then back the screw out 3 1/2 turns. Hold the adjustment screw and tighten the lock nut 10 ft-lbs. Install transmission pan/with gasket and refill transaxle to proper level. Test drive van. Be safe and block the rear wheels before you raise the van and try to work under it. Hope this will help you.

May 19, 2010 | 1997 Dodge Caravan

1 Answer

I replaced my transmission in my truck twice with different trannys. it will go in reverse and first but no 2nd or third gears.. I used the same torque is this the problem?


Some of these fords have a kickdown lever that needs to be adjusted at the carb. or injection end . never tip a used trany up side down it sends all the worn cluch and band debreas into the valve body and distroys the tranny A good tranny should not charge for this adjustment good luck CJ

May 11, 2010 | 1989 Ford F 150

1 Answer

Car will not go in reverse!


Have you changed your transmission fluid? I am assuming that it is automatic.Could be low on transmission fluid. Could also be filters in you tranny stopped up with slug/ gear shivers.Could also be band
in transmission needs adjusting.

Jul 02, 2009 | 2000 Hyundai Accent

1 Answer

03 tiburon stays in third gear


could be a few things... adjusting of the kickdown cable, over drive switch is not coming one, or od gear is blown.... bring it to a repected transmission shop or the dealer....

hope this helped

Jul 02, 2009 | 2003 Hyundai Tiburon

2 Answers

46RH transmission, no second gear.


Does it shift into 3rd at the right speed? If 2nd is just missing, try adjusting the kickdown band. (front band). The adjustment screw is on the outside of the case.

Apr 24, 2009 | 1999 Dodge Ram

1 Answer

Transmission shifts very hard from 1st to 2nd


may need to have the kickdown band adjusted. it is applied when the trans goes into second gear and in reverse.

Jan 29, 2009 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...