Question about 2008 Chevrolet Hhr

Open Question

Where is the crankshaft position sensor on a 2008 Chevy HHR SS 2.0

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

juncro
  • 467 Answers

SOURCE: i own a chevy hhr 2008,this morning im getting

please make sure the vehicle is fully in park, turn the key forward to on and try removing it, while depressing the brake pedal

Posted on Jul 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: crankshaft position sensor location

1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Posted on Sep 25, 2009

Testimonial: "Awesome. Thanks."

  • 540 Answers

SOURCE: 2002 chevy trailblazer with massive oil leak.

oil pan, or rear mainseal housings are common leaks on these... also if 4wd, diff runs thru oil pan..

Posted on Nov 29, 2009

  • 312 Answers

SOURCE: Key win't turn ignition switch in 2008 Chevy HHR

replace the floor shifter. there is a switch on the shifter that allows the key to move. gm has had alot of problems with these shifters.

Posted on Dec 27, 2009

roniecon
  • 6826 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know the location of both crankshaft position sensor on 2008 Chevrolet hhr plz thx


Only has one crankshaft position sensor ,an cam sensors . To change the crank sensor u would have to pull the starter ,located above starter .
Camshaft Position Sensor Replacement - Intake Camshaft Position Sensor Replacement - Exhaust
After a crank sensor replacement a
Crankshaft Position System Variation Learn has to be done !
Important: The crankshaft position (CKP) system variation learn procedure is required when the following service procedures have been performed, regardless of whether DTC P0315 is set:
?€¢
Engine replacement


?€¢
Engine control module (ECM) replacement


?€¢
Crankshaft damper replacement


?€¢
Crankshaft replacement


?€¢
CKP sensor replacement


?€¢
Any engine repairs which disturb the crankshaft to CKP sensor relationship

Important: The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
?€¢
CKP sensor activity--If there is a CKP sensor condition, refer to the applicable DTC that set.


?€¢
Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC that set.


?€¢
Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.

Apr 04, 2016 | Chevrolet Cars & Trucks

2 Answers

My HHR keeps setting the p0193 code. The symptoms are intermittent start and stall, run rough while stopped idling and starts, runs rough, stalls the restarts like nothing happened. and


This code refers to the fuel rail pressure sensor circuit being high. The two most common problems of this code are a faulty sensor and/or faulty pressure regulator. A wiring/computer issue can also contribute to this code. I have had success with numerous vehicles displaying this code by changing the fuel pressure sensor and correcting the problems you have stated

Jan 27, 2016 | 2009 Chevrolet HHR

1 Answer

Where is the ambient temperature sensor located ?


images for 2008 Chevrolet HHR LT Where is the .

Outside Temperature Sensor - Chevy HHR Network

www.chevyhhr.net/forums/...hhr-4/outside-temperature-sensor-30594/
Jul 9, 2010 - I had the outside temp sensor go on my 99 Buick. I don't know where it islocated on the HHR, but it was just a plug in sensor. Take out the old, stick in the new.... 2008 HHR LS 2.2 L Auto Built: 12-19-2007. Bought: 4-26-2009 Location of the ambient engine temperature sensor.... Help ...
Mar 26, 2013
Engine Temperature Sensor
Oct 6, 2011
Outside Temp Display
Dec 19, 2008
Outside air temperature problem
Oct 30, 2007
More results from www.chevyhhr.net

Jan 25, 2016 | 2008 Chevrolet Chevrolet HHR LT

2 Answers

Where is the crankshaft position sensor located on a 2008 HHR 2.2 is that ecotec engine


My info says it is located above the starter motor. Info says to remove the starter.

The info also says you have to do a crankshaft variation relearn procedure. I can't help you with that procedure.

Nov 18, 2015 | Cars & Trucks

1 Answer

What is a po532 code on a 2008 hhr ss


DTC P0532: Air Conditioning A/C Refrigerant Pressure Sensor Circuit Low Voltage.
The engine control module (ECM) monitors the high side refrigerant pressure through the A/C refrigerant pressure sensor. The ECM supplies a 5-volt reference and a low reference to the sensor. Changes in the A/C refrigerant pressure cause the sensor signal to the ECM to vary. When the pressure is high, the signal voltage is high. When the pressure is low, the signal voltage is low. When pressure is high, the ECM commands the cooling fans on. When pressure is too high or too low, the ECM will not allow the A/C compressor clutch to engage. P0532 Chevrolet Refrigerant Pressure Sensor Circuit Low Input

Oct 03, 2014 | 2008 Chevrolet HHR SS

3 Answers

Where do i add power steering fluid in a chevy hhr


They DO NOT have a power steering pump. This type of vehicle has an electric motor under the steering column that controls steering.

Apr 01, 2011 | 2006 Chevrolet HHR

1 Answer

Where is the crankshaft position sensor located on a 2006 Chevy HHR?


looking into the engine bay it is on the right side just below the fuel rail.

Aug 23, 2010 | 2006 Chevrolet HHR

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...