Question about 2001 Mitsubishi Galant

Open Question

Engine light my engine light came on it says crank senor fault and no activity and cam shaft sensor i changhed both sensors and didnt help the car runs fine tho what could it be

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ourhowse
  • 2007 Answers

SOURCE: Loss of power Mitsubishi carisma 1.9 DiD 2002

Change fuel filter.

Posted on May 20, 2009

Ad
  • 333 Answers

SOURCE: timming belt routing on 2002 montero xlt 3.5

The Marks are different (ie 12oclock/11:30 or so) as pictured here. I will post again if it is too small to read (sometimes fixya shrinks pictures)

4c8e43c.gif

Posted on Nov 08, 2009

johnjohn2
  • 5763 Answers

SOURCE: Where is the cam shaft sensor located on the

The cam sensor is located on the rear of the left cylinder head, heres a diagram to help you locate it.johnjohn2_32.gif

Posted on Dec 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI WE HAVE A CHEV OPTRA 1.6 2009.WHEN COLD IT RUNS FINE BUT WHEN HOT IT MISFIRES AND ENGINE LIGHT IS ON.WE DID REPLACE COIL. PLEASE HELP


engine light on ..any other fault codes

changed coil ..still the miss fire

could it be cam shaft sensor or crank angle sensor

are plugs leads and injectors working ?

26345869-z0jvk1iapsb122xkawhnenag-1-0.jpg

26345869-z0jvk1iapsb122xkawhnenag-1-1.jpg

26345869-z0jvk1iapsb122xkawhnenag-1-3.jpg

Nov 08, 2016 | Cars & Trucks

1 Answer

It won't start


check that the cam shaft is turning. (broken timing belt/chain) check immobiliser is operational. run fault codes and check for cam/crank position sensor fault.

Mar 14, 2014 | 1997 Isuzu Oasis

1 Answer

I have a 2001 galant with a 3.0 check engine light came on


I am assuming the engine will run. It could be a wiring problem or the cam and crank are not in sync.
I would need to know the actual codes to give more detail.

Feb 14, 2014 | 2001 Mitsubishi Galant

1 Answer

Engine check light is on, it cranks, diesel is coming to common rail but wont start.


run fault codes to find faulty sensors. Cam/crank position sensors. Check to see if the cam shaft is turning (broken timing belt)

Dec 26, 2013 | Nissan Cars & Trucks

1 Answer

Will a cam shaft senor keep my car from cranking when u cut it off I've changed both crank senor on it an it still want crank with out puting some quick start spray n it its a 2002 Buick century


when you say crank ,,, that means engine does not turn over when you turn the key to start position ,,,, as you said you use start spray this means engine is turning over ,,,,, i think you mean engine turns over but wont start,,,,,,, cam sensor will cause engine to be slower to start but you would be better to get the car plugged in to see what the fault codes are in the system ,,, also if no codes the data list of the engine sensors will show up a faulty sensor ,,, to be honest there is no point in spending your hard earned cash putting in sensors until you carry out a diagnostic check and only have to change the faulty sensor that shows up...best of luck

Dec 06, 2013 | Cars & Trucks

1 Answer

Do the engine senor make your car run bad and how much is a engine senor


There are all sorts of engine sensors that do different things to your car, I had a cam shaft sensor replaced as the car was stalling and jumpy to drive. The same applies with the exhaust sensor. little sensor/electrical problems can be awkward to find and depending on the sensor costly or cheap to fix.

Aug 24, 2012 | 2001 Buick Regal

1 Answer

Were is the cam shaft senor and the crank shaft senor located


this car does not have a camshaft sensor the distributor pick up coil acts as a cam sensor here is crank sensor info the crank sensor is located in front of engine just behind the crankshaft pulley using ohmmeter check resistance between terminals on sensor replace is not within specs cold 1630-2740 ohms hot 2065-3225 ohms if this is not the problem please reply to your post ill monitor it. hope this helps

Jul 26, 2010 | 1996 Toyota Corolla

1 Answer

Engine died at hwy speed crank/cam sensor faults


o1 cruiser spit and sputter go down rd put cam sensor and crank shaft sensor on wouldnt run at alll with new crank sensor had to put old one on please hel

Sep 29, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Crank shaft sesor/cam sensor problem?


If you had a fault with the crank sencer your car would not start.Sounds like the air flow meter is giving you the problems.

May 28, 2009 | 2005 Dodge Neon

2 Answers

2002 Jeep Grand Cherokee Lardo misfiring


You say you changed the cam sensor. A1391 code is a crank sensor on the top of the trans. bell housing.

Feb 22, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Mitsubishi Galant Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...