Question about 2005 Suzuki Aerio SX

1 Answer

Looking for location of crank sensor - 2005 Suzuki Aerio SX

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

Why? the ECU/pcm throwing codes for it ?
IT will , the eCU can be trusted to tell you any time it does mess up.!!!
but like all posts here, not one with engine size , type or option.
so no anwers. accurate.
1.3 L I4; 1.5 L I4; 1.6 L I4; 1.8 L I4; 2.0 L I4; 2.3 L I4; 1.4 L Diesel I4
which engine is yours, surely ,I'D NEVER GUESS?

why not read the FSM?? why not post symptoms. or DTCs or something, even country?
or get the day pass.?/???? at suzuki pit stop plus (google it) $4
and look it up (USA only sorry, and you didnt say that either?)

where is CKP?
well its not on the cam, (that be CMP)
the CKP on all cars, (99% pure ,like ivory soap)
is on the crank pulley, or the flywheel.
(some cars have it mid crank,rare)
lets try to list them all, what a challange... (the fsm has this and so does you can look at any time.)

2.0L and 2.3L is behind the flywheel,
there are 7 engines, the above to are common in USA> ONLY!
ok verbatim USA those 2 engines.
CKP removal,

  1. Remove the engine with transmission from the vehicle.
  2. Remove the transmission from the engine and then remove flywheel or drive plate from crankshaft.
  3. Disconnect connector from Crankshaft Position (CKP) sensor.
  4. Remove crankshaft position sensor (1) from cylinder block (2).

are you serious about this, just guessing>?
why guess. the ECU will tell you the CKP is bad, why not scan and drive car and see if the CKP fails. the ecu will in act report
1 drop out in 10 pulses on CKP
you can trust that... id bet your just guessing or listening to
non pro ECU/PCM people...

and if it fails. a DTC first check the connector. to it top side.
for loose. or corrosion or any forms of contamination.
this sensors must have perfect connections at all times.
and can fail easy of dirty connections. its not a hall sensor.
its only very weak coil, with 0.5v out put. 1/2 volt.
the fsm shows the scope view of it. and all techs check that.
using a DSO.

Posted on Feb 15, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the crank sensor located in an 89 Dodge Daytona

The info I looked at was for 2.5L engine, non-turbo.
If you have distributor, you don't have one. You may have a sensor inside distributor. Because the distributor usually works off the cam shaft, they don't call it a crank sensor.
Now, if you have a coil pack, you do have a crank sensor, some I've seen are on the tranny bell-housing. Or at the cranks shaft pulley in the front.
I did look at online partsbook for the engine I listed, no crank sensor listed.

Mar 14, 2016 | Dodge Daytona Cars & Trucks

1 Answer

Crank sensor location

Does it run? if so then the problem is not the crank sensor which is located above the starter motor in the tranasmission bell hopusing.

Apr 02, 2014 | 2003 Jeep Grand Cherokee

1 Answer

Where is located crank sensor izuzu trooper motor 3.5

look through right wheel arch and lift up rubber flap next to engine mount bracket is crank sensor

Mar 29, 2014 | 1999 Isuzu Trooper

1 Answer

Crank sensor location

The crank position sensor is on the top back side of the engine on the 3900 engine

Jun 02, 2012 | 2007 Chevrolet Uplander

2 Answers

Is it possible to get a diagram of the crank sensor for the 2004 hyundai sonata

Hi, in both engines the crank sensor is at the back of the engine by the transmission. The sensor is #10 in the diagram below and looks like the picture included.

4-cylinder crank sensor:

6-cylinder crank sensor:

May 06, 2011 | Hyundai Motor 2004 Sonata

2 Answers

What does the crank sensor look like?

I've attached a photo. It's under the timing cover near the crankshaft.

Oct 18, 2010 | 2006 Kia Sorento

1 Answer


crank sensors are usually located in/near the distributor.

Jun 07, 2009 | 2003 Nissan Sentra

1 Answer

Tryen to find location of the crank sensor on 1998 infiniti QX4

looking for crankshaft sensor on 1998 infiniti qx4

Mar 01, 2009 | 2004 Infiniti QX4

2 Answers

Car won't start

this is located on different spots on different engines if you go to autozone or napa get the price of the crank sensor they can give you a diagram of the exact location of where yours is

Jan 25, 2009 | 1997 Dodge Intrepid

1 Answer

Where is the crank sensor located on a 99 jeep cherokee

Your crank sensor is located between the engine and the trans. From the pass. side. look behind the engine and you'll find a wiring harness that goes to a sensor that is installed in the bell housing A 10mm bolt holds it in place. If you're replacing the sensor, make sure you look at the wiring harness that goes to it. The harness likes to come apart.

Jun 24, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides