Question about 2002 Jaguar S-Type

1 Answer



Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.

  • Jaguar Expert
  • 196 Answers

May i ask what type of s type you have 3.0?4.0? or 4.2?

Posted on Apr 14, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

We're is pcm located on 2002 lincoln continental

Hi Michael,

The PCM is shown in the top URL below...
(see what you are looking for)

It appears to be a small plug-in module... I would check immediately under the dash on the drivers side... as depicted in the bottom video.

Hope this helps

More Information for STANDARD MOTOR PRODUCTS RY116T,2002,continental,4.6l+v8,1387166,electrical-switch+&+relay,powertrain+control+module+relay,3688

BBB Industries Premium Alternators Starters Power Steering Products

Aug 13, 2016 | Lincoln Cars & Trucks

1 Answer

Where is the CPU on my 2001 Dodge Durango located

The PCM. They are referred to ECM PCM etc, if that is what your looking for it is inside the engine bay on the RH side (passenger) inner fender right about in the middle you will find a aluminum box with about 4 plugs plugged into it.

Aug 28, 2014 | 2001 Dodge Durango

1 Answer

Where is the pcm located on a 04 dodge ram truck

Stand at the passenger fender looking into the engine compartment. It will be located on your left side just over the edge of the fender. It is usually right against the firewall. Hope this helps.

Aug 18, 2011 | Dodge Ram 1500 Cars & Trucks

2 Answers

Looking for the PCM for a 2000 pontiac bonneville. please help. irritated and hot here.

The pcm or power control module is located on the drivers side of the engine.
The pcm relay is # 4 on the power distribution box in the engine compartment.
Also in the power distribution box in location # 6 is a 10amp mini-fuse for the
power train control. good luck!

Aug 04, 2011 | 2000 Pontiac Bonneville

1 Answer

Where is the Engine Control Module located on Diesel 6.0 Ford F350 2006?

The 2006 Ford F350 Powertrain Control Module is located in the Top, Middle of the Firewall when looking under the Hood, behind the Engine.

Here is the Service Procedure with Diagram of the PCM:

Mar 27, 2011 | Ford F-350 Cars & Trucks

2 Answers

Where is the engine control computer located on a 98 Pontiac Bonneville?

Hello kdolling
The powertrain control module(PCM) is located under the hood, at the left front corner of the engine compartment. Hope this is helpful.

Mar 12, 2011 | 1998 Pontiac Bonneville

1 Answer

Gauges not working no buss signal

That means you have no communivation to your PCM. Check the terminals at the PCM for any corrosion. Also in your relay box located under the hood there is an "engine inline" that can come loose so you can clean & tighten that up as well. The PCM might be bad.

looking down in the box. Top left hand corner,
X - Engine inline I was talking about

X - Ground wire hookup
X - Hot wire hookup
I hope you get the idea. I don't have a picture.

Feb 04, 2011 | 1999 Dodge Ram

2 Answers

Looking for my computer to get some numbers off of it its a 99 fordwindstar, 3.8

ECM is located behind the glovebox or behind console
The PCM is located behind the passenger's side of the firewall.

Mar 16, 2010 | 2001 Ford Windstar

2 Answers

Where is the crank sensor located on a 2000 grand cherokee limited 4.0?

The Crankshaft Position Sensor (CKP) is mounted to the transmission bellhousing at the left/rear side of the engine block. Engine speed and crankshaft position are provided through the crankshaft position sensor. The sensor generates pulses that are the input sent to the powertrain control module (PCM). The PCM interprets the sensor input to determine the crankshaft position. The PCM then uses this position, along with other inputs, to determine injector sequence and ignition timing. The sensor is a Hall effect device combined with an internal magnet. It is also sensitive to steel within a certain distance from it.
On 4.0L 6-cylinder engines, the flywheel/drive plate has 3 sets of four notches at its outer edge. The notches cause a pulse to be generated when they pass under the sensor. The pulses are the input to the PCM. For each engine revolution there are 3 sets of four pulses generated.
The trailing edge of the fourth notch, which causes the pulse, is four degrees before top dead center (TDC) of the corresponding piston. The engine will not operate if the PCM does not receive a crankshaft position sensor input.

This is a photo of the bell housing on the transmission:


Oct 07, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Jaguar S-Type Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

78238 Answers


Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides