Question about 2007 Mazda CX-7 Grand Touring

Open Question

How to adjust the beam on headlight on mazda cx7

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: I am trying to replace the low beam bulb on the

Open the 2007 CX-7 Owners Manual (here is you don't have one http://www.mazdausa.com/MusaWeb/pdf/manuals/2007CX7OM.pdf)
Go to page 8-35 (P. 331 in the pdf). Close the hood, you're in the wrong place. Remove the cover in the front of the wheel arch to expose the headlight assembly.

Posted on Jun 18, 2009

Hrnsly
  • 154 Answers

SOURCE: Timing chain broke on a 2007 cx7 w 65K miles

you need to take it to your local dealer and raise a big fuss because this is a known problem and if you yell loud enough you should be able to get this fixed under warranty.

Posted on Aug 12, 2009

  • 12 Answers

SOURCE: How do I change the bulb in the low beam headlight

Removing the bulb in a CX7 is a real PITA. If replacing the right bulb, turn the steering wheel all the way to the right, or do the opposite for the left side. (or you can opt to remove the entire wheel on the corresponding side) You'll need to remove 3-4 of the fender well clips with a phillips screwdriver being careful not to break them. Once the screws are removed, pry back the wheel well cover to access the back of the headlamp to change the bulb.

Posted on Feb 01, 2010

rickyrt441
  • 4399 Answers

SOURCE: mazda cx7. both high beams work and one low beam

Thanks for choosing FixYa and welcome. These new lights have two types lin one bulb, one for the low beam and one for the high beam. Find the bulb that isn't lighting for the low beam and replace it with a new bulb. If it doesn't work, you need to check the wiring to that specific light. Since it is only one, the new bulb should work.

Posted on Oct 01, 2011

SOURCE: How to adjust the height of a 2000 mazda protege headlights

Then you need a repair shop to that

Posted on Jul 26, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda Astina 1991


Find level ground with a wall. Drive up to the wall and mark where the centre of your headlights are on the wall with a piece of tape. Back up 20 feet and turn your headlights on high beam. Using the adjusting knobs make each light shine directly on the spot. Low beam adjusts itself down and to the left/right (away from oncoming traffic depending on what side of the road you drive on)

Nov 17, 2013 | Ford Cars & Trucks

1 Answer

How to achieve headlight adjustment


Check under the hood on top of the headlight assembly to find the adjustment screws for sealed beam unit.


-------------------------------------------------------------
Renault CAN Clip V123 Latest Renault Diagnostic Tool

Dec 19, 2012 | 2001 Mazda 626

1 Answer

Mazda cx7. both high beams work and one low beam works. how can i tell if its a headlight or some other problem


Thanks for choosing FixYa and welcome. These new lights have two types lin one bulb, one for the low beam and one for the high beam. Find the bulb that isn't lighting for the low beam and replace it with a new bulb. If it doesn't work, you need to check the wiring to that specific light. Since it is only one, the new bulb should work.

Oct 01, 2011 | 2000 Mazda MPV

2 Answers

How do I change the bulb in the low beam headlight in my 2007 Mazda CX7?


Removing the bulb in a CX7 is a real PITA. If replacing the right bulb, turn the steering wheel all the way to the right, or do the opposite for the left side. (or you can opt to remove the entire wheel on the corresponding side) You'll need to remove 3-4 of the fender well clips with a phillips screwdriver being careful not to break them. Once the screws are removed, pry back the wheel well cover to access the back of the headlamp to change the bulb.

Nov 04, 2009 | 2007 Mazda CX-7 Grand Touring

1 Answer

Aim hid headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 09, 2009 | 2007 Mazda 3

1 Answer

My headlights wont adjust by the motors is there a manual adjustment on them i have a mazda 6 2.0 ts and if so where is it


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 06, 2009 | 2004 Mazda 6

2 Answers

Can't find the adjustment knob for the headlights on a 2008 Mazda


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jun 09, 2009 | 2008 Mazda Mx 5 Miata

1 Answer

I am trying to replace the low beam bulb on the passenger side of a 2007 Mazda CX7 . Can't seem to figure out how to get to it. Any help?


Open the 2007 CX-7 Owners Manual (here is you don't have one http://www.mazdausa.com/MusaWeb/pdf/manuals/2007CX7OM.pdf)
Go to page 8-35 (P. 331 in the pdf). Close the hood, you're in the wrong place. Remove the cover in the front of the wheel arch to expose the headlight assembly.

Jun 08, 2009 | 2007 Mazda CX-7 Grand Touring

1 Answer

How do you adjust the headlights on a 2002 Mazda Miata?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jan 04, 2009 | 2002 Mazda Miata

Not finding what you are looking for?
2007 Mazda CX-7 Grand Touring Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...