Question about 1998 Saturn SL

1 Answer

No pressure on the clutch pedal - 1998 Saturn SL

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Your clutch has Burt out not an easy job you'll have to pull that transmission to replace It

Posted on Feb 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Mazda MX6 Clutch pedal has no push back from floor but still shifts


I am not a mazda guy but it sounds like the pressure plate is bad. Have you check the clutch linkage to be sure something did not slip or break. If so I would be looking at the clutch pressure plate.

May 18, 2017 | Mazda Cars & Trucks

1 Answer

Clutch pedal sticks and trouble shifting


It happen twice to me ,spring come out from clutch disk and jam the pressure plate, check transmission shift very well with engine stopped, When you push the pedal you push the spring and put pressure on the disk

Mar 30, 2014 | 1999 Chevrolet Camaro

1 Answer

No pressure on clutch pedal


Is the clutch pedal cable or does it have a crutch master cycl or slave cycl, if it is cable may need to be adjusted if it has a clutch master and slave you need to bleed it.

May 18, 2012 | 1986 Chevrolet Chevy

1 Answer

1997 Probe Gt, 5 speed, 2.5 L V-6; 77,750 miles: replaced clutch master cylinder 11/15/2010. Clutch free play okay, pressure to push clutch pedal down- okay (these conditions apply to vehicle after...


THe problem can only really be with the clutch master cylinder. What you describe sounds like the master cylinder is not relieving pressure and this is building up in the salve cylinder, applying pressure to the pressure place and causing the clutch to slip. Can you make the problem go away even temporarily, if you open the bleed screw on the slave cylinder? You say that the free play is correct, but is the master cylinder returning fully to its released position?

Jan 26, 2011 | Ford Probe Cars & Trucks

1 Answer

2002 Kia Sportage Car spongy clutch pedal Answer The clutch pedal is very spongy, and sometime has not pressure on the pedal at all when the vehicle... (More) The clutch pedal is very spongy, and sometime...


The spoongy feeling is a defective clutch slave cylinder. Generally a cluthc will not slip because of a pressure issue with hydaulics.

If the clutch is slipping with your foot off the pedal it defineately is time for a clutch job... Best bet is to get it inspected to be sure.

Jan 04, 2010 | 2002 Kia Sportage

2 Answers

1993 toyota paseo. When i depress the clutch theres no pressure


Your clutch hydraulic system is compromised. Look under the dash, where the clutch pedal has a rod going thru the firewall. If it is damp with oily fluid, your clutch Master Cylinder is leaking. Also, on the side of the transaxle, there is another cylinder, the clutch Slave Cylinder. It can be leaking, also. In any case, with a condition such as yours, I would recommend that you replace both the clutch master and slave cylinders. Over time, they can wear ionterally, and no develop the proper flui pressure to release the clutch.

Oct 19, 2009 | 1993 Toyota Paseo

2 Answers

Abnormal clutch pedal operation


You've replaced the master, the slave, now I would check to see if the throwout fork will move by hand. If you can move the fork by hand I would say that your pressure plate and or throwout bearing are worn out. First try to just gravity bleed the system. If that doesnt work, it may be time for a clutch, pressure plate, and bearing. The pressure plate spring pushes the pedal back up and depending on how many miles and driving habit those little arms on it break off and just wear out. I hope this helps you.

Aug 19, 2009 | 1997 Mitsubishi 3000GT

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

2001 Honda Accord Clutch Issue


check the actual pedal and clutch linkage.  Also look for a fitting thats emitting air into the system.

Mar 24, 2009 | 2001 Honda Accord

Not finding what you are looking for?
1998 Saturn SL Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...