Question about 2001 Hyundai Tiburon

1 Answer

Fly wheel bolts keep coming lose - 2001 Hyundai Tiburon

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 40,775 Answers

This happens when the flywheel is out of balance. Check that the mount area is clean and free of burrs on the crank shaft. Ensure that the threads in the crank shaft are burr free. ensure that if a dowel is used to locate the flywheel that it is in place . Use the fly wheel bolts once on;y. Use a low strength loc-tite compound on the bolt threads and tighten to specified tension (normally around 90-100ft/lbs.) use a tension wrench for this.. Next pay attention to the clutch pressure plate and that it is being held in place by the correct bolts . Small shanks that act as dowels to locate the plate exactly in position. Use locating dowels if there is holes in the flywheel for them . clamp a flat bar to thye engine flange and place it at the circumference of the flywheel and turn the engine over and see if it hits the bar in one spot or is the same distance away all the way around . Adjust the space till there is virtually no clearance under the bar. Then place the bar on the face of the flywheel and see if the flywheel is wobbling against the bar .You can use a dial indicator for these to teats .

Posted on Feb 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fly wheel torque for fiat siena 1,2 2001


Flywheel bolts (always use new bolts)
15Nm / 11 lbf/ft
Then a further 40 degrees of bolt head rotation..

Jun 18, 2016 | Fiat Cars & Trucks

3 Answers

Hi. I did unscrew all 5 bolts on my audi a6 wheel and I can't get off this wheel. What happens and what should I do?


GIVE TIRE SIDEWALL GOOD KICK TIRE SHOULD COME OFF.MAKE SURE VECHICLE WEIGHT OFF THE TIRE. IF NOT TIRE IS NOT GOING TO COME OFF.

Sep 05, 2011 | Audi A6 Cars & Trucks

1 Answer

How to change the clutch , pressure plate , and throout bearing on a 95 ford ranger 4x4 4.0 v6


The 1st step is to loosen your bell housing bolts and drop your starter. The remove your drive shafts the front drive shaft will slide out from the front and then pull it back to the rear. Then you must take your shifter lose from the Trans not the diff. then drop your cross member. Do not take the transfer case lose from the trans. If you can help it. You will then remove the trans. And unbolt the pressure plate. And everything should come off, make sure when you reinstall the clutch plate that you make sure the side that said to fly wheel is against the fly wheel. Make sure you tighten the pressure plate and clutch plate up with you line up tool all the way in and don't be afraid to tighten down on it. Because it isn't easy getting the Trans back up in there. The reassemble in the same order.

Jun 08, 2011 | Ford Ranger Cars & Trucks

1 Answer

Cant get fly wheel bolts off \r\n2001 eclipes


I'd spray spray down with a good penetrating oil, let set for 24 hours or so, then using a hammer hit the bolt on the head (carefull of the fly wheel) then you may want to actually try to ever-so slightly tighten the bolts then go back and try to remove.

I hope this may have assisted,
Tom

Jun 05, 2010 | 2001 Mitsubishi Eclipse

2 Answers

Cant get fly wheel off . Droped trans & have fly wheel exposed...6 bolts, And they wont come off.


Soak in penetrating oil and remove bolts using air line. If no access to air tools then use breaker bar with constant pressure (no not bounce)

If no joy then you wheel need to heat the flywheel - if you have to do this replace the rear main seal aswel.

Regards

Lloyd Six

Apr 30, 2010 | 1986 Ford F150 SuperCab

1 Answer

At idle it knocks when i gear it does not


few thing, possible
lose torqconverter bolts,
broken fly wheel,
or a rod, it will have to go to the shop for proper check out

Apr 14, 2010 | 1990 Dodge Dakota

1 Answer

Having trouble removing crank pully on a 1997 mitsubishi mirage


TURN OFF RADIO TO KEEP FROM LOSING RADIO CODE DISCONNECT NEGATIVE BATTERY CABLE. YOU WILL HAVE TO REMOVE STARTER FLYWHEEL COVER THEN REMOVE STARTER.I WOULD GET A LARGE SCREW DRIVER WEDGE IT SOMEWHERE ON THE FLY WHEEL.MAKING SURE NOT TO DAMAGE ANYTHING IT WOULD STOP ENGINE FROM TURNING WHILE I LOOSEN THE CRANK PULLEY BOLT.

Sep 14, 2009 | 1997 Mitsubishi Mirage

1 Answer

Audi A6 1.9Tdi 53 plate


yes you must remove the gas with a special machine ,and flywheel bolt is about 8 bolts normally .

Jul 03, 2009 | 2000 Audi A6

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...