Question about Jeep Liberty

1 Answer

The ignition key will not start the vehicle. I have to use the remote starter then insert the key into the ignition to keep the vehicle running. When I turn the ignition off there is alow buzzing noise. To restart the vehicle I have to use the remote starter then insert the key into the ignition again to keep the vehicle running. The key will not turn the engine over nor start the vehicle. The lights and the dash lights come on. What can the problem be?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jeep Master
  • 786 Answers

The ignition switch is not reading the chip in the key, Triggering the anti-theft mode in the ECU.

Posted on Jun 04, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Clicking Noise when trying to start vehicle

check your key remote if it is not programmed the alarm will go into the kill switch mode and will not allow you to start your engine Having the same trouble with one of my keys I haven't found a way to reprogram it without calling dealer and paying a chunk.

Posted on Aug 04, 2008

  • 19 Answers

SOURCE: Toyota starter problrm

NEED TO REPLACE STARTER.

Posted on Mar 05, 2009

  • 1 Answer

SOURCE: Sensonic gearbox

Hi had same problem last Friday you can put a fuse in (30 amp) for gearbox and it will start when you turn key but you will not be able to select a gear I'm 100% sure it's the sensonic activator box you can pick one up for about £150-200 second hand.
Dave

Posted on Oct 02, 2009

CMR_Racing
  • 24 Answers

SOURCE: turn key nothing happens no clicking noises

Starter, altinator

Posted on Dec 13, 2009

  • 146 Answers

SOURCE: jeep won't start. turn the

clicking when you turn the ignition on most vehicles could be one of two things. First the selenoid for the starter. Second the batterry is worn out or drained. Since your jeep starts with the remote its not your battery. Lucky for you your remote starter is like having a second selenoid. If you are so inclined you might try to fix it yourself. Open the hood. Have someone else turn the key. Follow the sound. I don't have a jeep of that model to look at but It could possibly be comming from a two post terminal that is realatively easy to change. If you are worried about reassembly take pictures before you start. Clean all connections that look corroded.

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 ford f-150 truck has a coolstart remote , doors lock, and unlock with remote but engine does not start


It may be the Security module. The "cold start" routine is necessary to make the engine run cold. When you are already inside the vehicle and turning the ignition switch it is not using the "wireless" feature of the FOB's. The ignition switch is hard wired to the vehicle module and would be sending the signal through a wired connection. For the warm start, the "cold start" sequence is not needed and all this proves is you have spark and fuel. Many engines are running too lean to start without the "cold start" sequence. Another remote possibility is a stuck temperature sensor is keeping the cold start off, but that does not explain the truck starting with a key.

Jan 23, 2017 | Ford F-150 Cars & Trucks

1 Answer

I called myself programming the new keys for my pt cruiser, but,it didnt take. At first it would start and run for a few seconds, now it wont turn over.what did I do wrong and how can I fix this?


Takes the master key to get it started again. The security gives you 3 tries to get the vehicle started, after the third time, it kills the starter.
2002 Chrysler PT Cruiser Note: You must have two valid keys to add a new key to the system.
1. Insert the first valid key into the ignition switch. Turn the ignition switch to the
ON/RUN position for at least three seconds, but no longer than 15 seconds.
Then, Turn the ignition switch to the LOCK position and remove the first key.
2. Insert the second valid key into the ignition switch. Turn the ignition switch to
the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound.
In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch
to the LOCK position and remove the second key.
3. Insert the new key into the ignition switch. Turn the ignition switch to the
ON/RUN position.within 60 seconds. After 10 seconds, a single chime will
sound. In addition, the Vehicle Security Light will stop flashing. To indicate that
programming is complete, the Vehicle Security Light will turn on again for
seconds and then turn off.
The new key is now programmed. The Remote Keyless Entry transmitter will
also be programmed during this procedure.
Repeat this procedure to program up to eight keys.

Oct 09, 2016 | Cars & Trucks

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

2 Answers

I have a 2003 hyundai sonata and i dont have the remote for the stock alarm. My alarm keeps going off and my car wont start. I bought a new battery and even tried the key in the door still no luck.....


The 2003 Sonata is equipped with a 'starter KILL' burglar alarm system with disables the starting system (using a N/C 'contacts' configuration instead of a N/O contacts configuration). N/C=Normally closed, and N/O=Normally open contacts. When the alarm goes off with a MY Sonata, the only way to DISARM it is with the key fob (remote) originally programmed for it (unless you purchase a new remote & have it programmed for the vehicle at an authorized Hyundai Service Department). NOTE: So long as the keyless entry & burglar alarm system is functioning/operating normally, the alarm will keep going off and the STARTER KILL function will still prevent you from starting the vehicle. One option is left without purchasing a new remote and having it programmed.
1. When the alarm goes off, get into the vehicle and insert the ignition key into the ignition.
2. Turn the key to the 'RUN' position (NOT the ACC position) and wait for the alarm to STOP (usually about 3 to 5 minutes).
3. The engine should then start using the ignition key.

If this procedure doesn't work, the problem will need further diagnosis by a qualified/certified Hyundai Service Technician.

Hope this helps

Aug 27, 2011 | 2003 Hyundai Sonata

1 Answer

I just recently purchased a 1996 cadillac el dorado etc. it starts then shuts right off. i dont know if it is something wrong with the anti theft system. maybe the keys. i need to know how to check this. i...


Heres the deal. When you put a remote starter on this year Cadillac (and about 100 other GM models) you have to bypass the security system. On these vehicles, that chip in your key has to communicate with the ignition/lock cylinder and then the TDM (computer) to allow your starter to start and/or allow the injectors to continue working. So what people will do is "bypass" the key and lock cylinder to fake the TDM into believing it has the correct key chip inserted. This allows you to remotely start a vehicle with an antitheft. My guess is that your TDM has now failed. Since the remote starter (which is hooked directly to starter) works and the key doesnt AND we already know that the system has been altered.... I'd put money on the TDM (theft deterrant module). Check out this link. You'll find an answer to your problem for sure. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Apr 14, 2011 | 1996 Cadillac Eldorado

3 Answers

MY PT Cruiser Functional transmitter and the one to be programmed both have no "PANIC" Button . How I programme the spare Fob


If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.

Sep 05, 2010 | 2001 Chrysler PT Cruiser

2 Answers

When I insert key to start the car it will not turn at all. What is this part called?


The component is a starter. When you insert your key into the ignition and turn it, you switch on the power to the coil and vehicle computers. By turning the key to the start position it will supply power to the starter and solenoid which cranks the engine until you release the key allowing to return to the ignition on position. If the battery is weak the starter solenoid may engage producing a clicking sound, but it will not crank the engine. Another test is to turn on the dome light and try to start the vehicle, if you see the dome light dim when you are trying to start the car the battery is weak or the starter has a short. Starters are temperamental at times and can be intermittent working sometimes and malfunction other times. Your ignition switch, fuse, or relay could also produce symptoms of your vehicle not cranking.

Jul 21, 2010 | 2004 Chevrolet Cavalier

1 Answer

Resetting a Key fob on 2007 Honda Pilot


to program a key fob- get in vehicle and close all doors. insert key into ignition, have all the key fobs you want to program for this vehicle in hand, programing erases all old fobs. turn the ignition switch to on(all dash lights light up, on click before starting the car). then hit the lock button on one of the fobs. turn the ignition to lock. turn the ignition back to run and press the lock button again from the same remote. repeat untill all the locks cycle. ones the locks cycle keep the ignition in run and press the lock button on each key fob(the ocks will cycle each time a button is pressed). then turn the ignition to lock after all fobs have been programed

Dec 31, 2009 | 2009 Honda Pilot

1 Answer

Remote starter on a 2004 Accord with V6 engine


remote starter is designed to shut down the vehicle if there is no key to drive with. This is a security feature so that unauthorzed drivers cannot steal it. to answer second question the purpose of remote starters is to allow you to heat up the vehicle so it is an ice cube when you are ready to drive. Not sure what remote I cannot answer the horn question. Need more on what remote starter you have model number and make

Apr 20, 2009 | 2004 Honda Accord

3 Answers

Key Does Not Work


It could be that chip inside key just went bad. Do u have a 3rd key? That works? If so take the 2 good keys and turn the igntion to run postion for 3 secs each then do the same for the 3rd key and this will reprogram it if the chip is ok. If you do not have 2 good keys then u will have to have a scan tool that will link up with PATS system and perform security access to reprogram it.

Feb 12, 2009 | 2005 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...