Question about 2000 Nissan Xterra

Open Question

I have a 2000 nissan xterra and both of my fog lights doesn't work, I checked the bulbs and they are fine. Could it be a fuse that is not labeled on the panel?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

j_del
  • 1586 Answers

SOURCE: How do you change the fog light bulb on 1993 zx?

Take out the small screws that hold your turn signal/marker lights on. This will allow you to reach in and undo the three (if I remember right) 10mm nuts on the back of the fog housings that hold them in the bumper. Once they're removed, press on the back of the fog housing and the foglight assembly will pop out of the bumper. Then you can replace the bulbs.

What I did on my Z is something you might consider - while I had them out, I took them apart (just a couple screws and bolts, very easy). Open it up so that you have access to the glare guard - the cup that sits in front of the bulb. This blocks forward projection of the light, and instead bounces it onto the reflector to be spread very wide (but not far forward) in a fog beam pattern. I used pliers to physically break the guard off the housing, so that instead of a wide, shallow fog pattern, I had a forward-projecting driving beam. I also swapped the 35w OEM bulbs for 55w higher-output superwhite bulbs (this increase in power consumption is not enough to cause any risk to the wiring or fusing, by the way - it worked for years for me). Then put them back together and reinstall them - you'll find a drastically improved light pattern for night driving, and they're still low enough to the road to cut under most fog. Especially since I always felt that the Z headlights were pretty pathetic for output (at least until I installed HID lighting), this was a great mod to make to the car.

Posted on Sep 04, 2008

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Posted on Sep 06, 2008

  • 383 Answers

SOURCE: 2005 Nissan Maxima SE Fog light replacement

jorgeva: on the driver's side to gain access, you must remove the air cleaner assembly. At that point, you can see the back of the light which has a plastic cap. Rotate this "counter clockwise" and you can pull it back from the back of the lamp housing. From there you will see how the bulb it self is plugged in, which is obvious. Unplug it. There is a "spring "like latch retainer to hold the bulb in place. Unlatch it, remove the bulb and install the new bulb.
CAUTION!!!!!!! DO NOT TOUCH THE GLASS AREA OF THE NEW BULB! Only handle the rear section. Reassemble in the reverse order.
The right side will require the removal of the windshield washer tank.
I trust this will have answered your question. If you would, let me or FIXYA know if I have solved your problem......

Posted on Apr 18, 2009

SOURCE: brake lights went out, changed bulbs, checked fuse, still wont work

You have to check the brake light switch which should be around the brake pedal on the upperside.
Ones located rremove the wires tht go to the switch and jump them by using a piece of wire, thn check if the brake lights come 'on'. If they do , thn its the switch tht may need replacing or even sometimes adjusting inorder to operate.
Hope this helps.

Posted on May 10, 2009

  • 6 Answers

SOURCE: 2000 nissan xterra hesitating when engine is warm

We are having the same problem. We are right now changing the crankshaft position sensor along with the intake and manifold gaskets.

Posted on May 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My son is in college and called tonight. He has a 2000 Nissan XTerra. When he puts his head lights on, his hazard lights flash. Any ideas on what might be wrong and how he can fix it?


Have him inspect each bulb for the tail and brake lights as well as the front amber light bulb filaments inside the bulb. There are two in each bulb. If any one of them touches the other then you'll get a back feed that will cause the flashers to start working when they aren't supposed to.

Oct 07, 2014 | 2000 Nissan Xterra

1 Answer

Turn signals don't work in my 2000 Nissan Xterra. Fuses are OK


Could be a bad multifunction switch or even the flasher relay

Apr 19, 2013 | 1999 Volvo S80

2 Answers

My fog light don't work


fog lights not working 2005 maxima. is there a fuse for the fog lights?

Apr 22, 2010 | 2004 Nissan Maxima

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

1 Answer

The rearview mirror on a 2001 Nissan Xterra.


It may be a fuse, but I think that all the dash lights are on the same fuse and if they work, then there is a bulb located inside the rear view that needs to be accessed to be replaced. I would check all fuses with key on and lights on, both sides with a test light, and if all read good then it'll be the bulb.

Jan 31, 2009 | 2001 Nissan Xterra

1 Answer

2000 Xterra Brake Lights


Check the brake light switch located near the brake petal.

Nov 16, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...