Question about 2004 Nissan Quest

Open Question

Nissan quest 3.5L top dead center - 2004 Nissan Quest

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 26 Answers

SOURCE: timing belt

try removing spark plug No1 and insert a rod or fine screw driver and detect the top dead point of the piston.

Posted on Jul 06, 2008

Ad
boysor2933
  • 293 Answers

SOURCE: 1994 nissan pickup 4x4 2400 where should the rotary point when at top dead center

Do you mean the distributor pick-up rotor? If it is and you are referring to the number 1 piston, the tip of the pick-up rotor should be a little bit pass the #1 contact terminal of the distributor cap. The tip should be exactly at the terminal when the piston is at the specified position before the top dead center (BTDC).

Posted on Oct 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the ignition timing for 2002 nissan hardbody 2000i 16v


Here are the 3 engines listed for this year. IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 2.4L SFI 4cyl

The Ignition Timing

18-22 DegreesBefore top dead center - When throttle positionsensor disconnected and using suitably programmedscan tool.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (750-850 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (700-800 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI SC 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chockdrive wheels, curb idle speed (700-800 RPM)transmission in neutral.

Jun 05, 2015 | Nissan Hardbody Cars & Trucks

3 Answers

If I accidentally pulled distributor out without knowing exact location of rotor how do I find correct placement for rotor? 2002 Nissan quest


This is just a shot in the dark... But i THINK the # 1 cylinder needs to be @ top dead center.... And the rotor needs to be pointing at the part of the cap where the spark plug wire connection for cylinder #1 is.

Mar 02, 2015 | Nissan Cars & Trucks

1 Answer

Ignition timing



1991 Nissan/Datsun Truck D21 Truck 2WD 3.0L FI 6cyl

The Ignition Timing
15 Degrees Before top dead center*Warm idle speed 750 RPM*Transmission in neutral (Parking brake engaged)*All accessories off.

1991 Nissan/Datsun Truck D21 Truck 2WD 2.4L FI 4cyl

The Ignition Timing
10 Degrees Before top dead center*Warm idle speed 800 RPM*Transmission in neutral (Parking brake engaged)*All accessories off.

Mar 24, 2014 | 1991 Nissan Pickup

1 Answer

My nissan quest is crank no spark i put new timing belt new spark pluck new crankshaft sensor n new distributer still no start


putting on a timing belt for your nissan is a delicate process, it requires a lot of experience, attention to detail, and precise installment. its not like changing a filter. unless you are an experienced tech, or had one do the proceedure, avoid it. the details like setting #1 piston to top dead center, before removing all the items to get to the belt. and positioning the cam gears, etc., etc., etc.,.............thats most likely what your problem could be, just sayin.........................talking from experience !!!!!!!!!!!!1

Mar 03, 2013 | 1999 Nissan Quest

1 Answer

Where is the crankshaft sensor for the 1997 nissan quest located?


For 1997 Nissan/Datsun Truck Quest Mini Van 3.0L SFI 6cyl the Crankshaft Position Sensor is located: Under hood, center, upper engine area, mounted on top front driver side of engine.

Hope helps (remember comment and rated this).

Jul 26, 2010 | 2004 Nissan Quest

1 Answer

How do i mark my timing belt and take it off while doing a head gasket job on a 91 honda accord lx


put it at top dead center, also when you remove the cover rotate until mark on crank gear lines up with mark on oil pump housing ,it right behind the gear, also you will see notches on the cam gears and the rear cover those should also line up when crank gear is aligned, sometime marks on cams are 180 degrees off which just means crank has to be turn one more time, then double mark gears that all, good luck.

Nov 13, 2009 | 2001 Nissan Quest

1 Answer

The A/c does not work in the rear.I have a 1996 nissan quest


you have a bad solder joint in your heater control head. If you can solder, you can fix it. I will fix it for $25 and send you a control head. Then you send yours back to me.

Here's our Villager/Quest web site.

http://groups.yahoo.com/group/villagerquest/links

4b29200.jpg
You have to remove 4 plastic screws on console bottom. Then remove 2 screws at bottom of center trim panel. Then remove ash tray and 2 screws just above tray opening. Then 2 screws at top of center trim panel. Then pull off center trim panel. It has 2 spring clips in center.
Then remove 4 screws holding control head in.
Remove all electrical connectors.
remove thin plastic cover on bottom of unit. 2 plastic clips hold it on.
remove circuit board, and look on back side for crack around solder joint that is circled in red on picture. Or the joint next to it.
resolder the cracked joint. Don't heat the joint too much. Just enough to get solder to drop on to it.

Jun 29, 2009 | 1996 Nissan Quest

1 Answer

Set timing after replacing distributor


Ignition Timing
  1. sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Parking brake control should be applied.
    Depress the parking brake pedal, and warm the engine to the normal operating temperature.
  2. Turn off all electrical loads.
  3. Start the engine and rev it to 2000-3000 rpm two or three times and allow the engine to return to the idle.
  4. Check the idle speed. The idle speed should be between 700-800 rpm in PARK (P) or NEUTRAL (N) position.
  5. NOTE: Make sure that the timing pointer is pointing to the 15° Before Top Dead Center (BTDC) mark on the crankshaft pulley. Each notch on the crankshaft pulley represents 5 degrees.
    Check the ignition timing with a timing light.
  6. If the marks are not aligned, loosen the distributor bolt and turn the distributor to make the adjustment. The ignition timing should be between 13°-17° BTDC.

Feb 22, 2009 | 1999 Nissan Quest

1 Answer

1999 nissan quest


Rigoe the points for the timing belt are usually located on the sprokets in conection with marks or dots on the engine block some where around the sprockets that hold the timing belt. Remenber to bring the piston number one to TDC (top dead center), this means you have to locate the piston number one, take the spark plug out and turn the cranshaft (the one with the pulley) by hand until the piston is all the way up. On the distributor the rotor should point to the spark-plug wire number one (you can make a mark outside of the distributor cap where the number one spark-plug wire is pointing so when you take the cap off you can see if the rotor is pointing the same direction). With the timing belt cover off you are going to be able to aling all this points at the exact locacation all together. So we have: Piston number one at TDC, The rotor(enside the distributor cap) pointing to the number one spark-plug wire, and the mark of the sprockets pointing the marks of the engine block( litle dot or dash). If you get all this right you are have done a good job and ready to make a trip you can get all this just by turning the cranshaft by hand with a rachet and a big socket. God bless you.

Dec 06, 2008 | 1999 Nissan Quest

1 Answer

Nissan Quest 1996 minivan


you need to remove the lower balljoint and the center nut and it should come right out. use pb buster or wd-40 on the splines. they tend to rust up

Oct 02, 2008 | 1996 Nissan Quest

Not finding what you are looking for?
2004 Nissan Quest Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...