Question about Cars & Trucks

Open Question

2001 lincoln town car 4.6 valve cover removal

How to remove left valve cover

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: heat wont work 2001 lincoln town car cartia

Hello Callahan5922....this sounds like a stuck blower motor resistor. I assume the blower won't function in the a/c mode either? If you have a digital multimeter you can check this. I believe it's fuse #2....if the digital indicator goes up or down when you increase or decrease the fan speed thats good. Locate the blower motor resistor....you wil find it located on the fire wall behind the right valve cover hiding behind the heater hose, it's about the size of a cigarette pack. With the engine off, and key in on position, turn the A/C on High, and rap a tap tap tap on the resistor. You might be suprised when the blower motor takes off a runnin,
I hope this is the answer you need and i was able to help solve this for you. Good luck...

Posted on May 13, 2009

  • 50 Answers

SOURCE: how to remove starter from 96 Lincoln town car

If this is a 96 LINCOLN TownCar, then "techbuster" is way off. The 96 didn't have a solenoid on the fender. The starter is located under the passenger side of the engine just ahead of the transmission. It has three bolts holding it on. Remember to disconnect the battery first. The lower starter bolt can be accessed easily, but the other two could be quit difficult. They can be best removed with a very long extension inserted past the passenger side motor mount. The single ignition wire and the starter cable can be removed after the starter is tilted forward to remove it. The starter can then be tested as can the solenoid to determine which is the problem.

Posted on Oct 12, 2009

  • 1 Answer

SOURCE: 2001 lincoln town car winshjield wiper

where is the fuse box for my 2001 lincoln towncar looking for windshield wiper fuse because they wont turn on what so ever

Posted on Dec 24, 2009

kennyz195
  • 61 Answers

SOURCE: 2003 Lincoln Town Car - Power window switch removal/installation

SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.

  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 03 lincoln town car with the 4.6l v8 and cant figure out how to remove the cover that covers the engine


At the rear center or the cover is 1/4" square drive headed bolt -remove using your 1/4" ratchet with a 1/4" extension . lift rear of cover and push cover forward off the two horizontal tabs facing forward in front. reattach in reverse order.

Feb 22, 2015 | 2003 Lincoln Town Car

2 Answers

Remove headlight assembly from 2006 Lincoln town car


I've done it so many times for exact 2006 TC.

1. Remove black plastic cover if it's equipped by twisting 5 fashioners.

Those are looked like screws but plastic fashioners.

2. Remove 3 screws (two on top one on bottom) Do not touch adjuster screw.

3. push down plastic hook between two top screws and pull whole assy. be careful not to make scratch on bumper.

Remove wire connector before you pull it out completely.

4. After you remove assy, take 6~8 screws on back cover, then you will see light valves.

I have problem to upload pictures now.

I will upload them as comment to myself.

Jan 30, 2015 | 2006 Lincoln Town Car

1 Answer

92 lincoln tapping on top end


need to remove valve covers and run engine with valve covers removed you will probably find worn valvetrain components causing the tapping

Apr 18, 2013 | 1998 Lincoln Town Car

1 Answer

Where are the Spark Plugs located on my Lincoln LS 2001 3.9L? How do I remove and replace the Spark Plugs?


Remove coil covers,by removing (6) 7mm screws. Covers are on top of valve covers

Remove (1) 7mm screw holding each COP Ignition Coil

Remove spark plugs.

Motorcraft--AGSP32FSM
NGK--FR5AP-11E Both one in the same

NGK--6569 (FR5AP-11E) Special Plug,different center electrode diameter

Sep 19, 2010 | 2001 Lincoln LS

1 Answer

Need to know where the pcv valve is located on a 2001 lincoln ls 3.9 and the price


PCV valve is in one of the valve covers with a hose attached. Pull the valve straight out of the valve cover and remove the hose. Cost is about $5 or less. Any more questions, please let us know.

Sep 11, 2010 | 2001 Lincoln LS

1 Answer

Where are spark plugs in a 1998 lincoln town car cartier?


they are "coil on plug" design, so you have to remove the ignition coils to get to the plugs.
they are along side of the valve cover near the fuel injectors

Mar 28, 2010 | 1998 Lincoln Town Car

1 Answer

How to change out valve cover gaskets on a 1989 Lincoln Town Car


This is All you need for this Repair, ALSO Be Sure ALL GASKET SURFACES ARE VERY CLEAN. This Engine Requires MORE than MOST ALL Engines do for this Repair.

REMOVAL

  1. To remove a valve rocker arm cover from the RH cylinder head, disconnect PCV closure tube from oil fill stand pipe at rocker cover.
  2. Remove the Thermactor bypass valve and air supply hoses as necessary to provide clearance.
  3. Disconnect the spark plug wires from the spark plugs using Spark Plug Wire Remover T74P-6666-A or equivalent. Do not pull on wire. Remove the wires and bracket assembly from the rocker arm cover attaching stud and position the wires out of the way. ALSO MARK THEM AS TO WHERE THEY CAME FROM !!!
  4. Remove upper intake manifold.
  5. Remove attaching bolts and remove the cover.
INSTALLATION

  1. Clean the valve rocker arm cover(s) and the cylinder head gasket surface(s). Position a new service valve rocker cover gasket.
  2. Position the cover(s) on the cylinder head(s). The cover is tightened in two steps. Tighten the bolts to 14-18 N.m (10-13 lb-ft). Two minutes later, tighten the bolts to the same specification.
  3. Install the crankcase ventilation tube in the RH cover.
  4. Install upper intake manifold.
  5. Install the spark plug wires and bracket assembly on the rocker arm cover attaching stud. Connect the spark plug wires. Install the air intake duct assembly.
  6. Install the Thermactor bypass valve and air supply hoses (if required).

Oct 03, 2009 | 1989 Lincoln Town Car

1 Answer

How do i replace the left valve cover gasket - I cannot remove the valve cover


someone may have used a tuff gasket cement.  You just have to remove all the bolts and connections and perhaps hit it with a rubber mallet to loosen it. 

Mar 23, 2009 | 2000 Lincoln Town Car

1 Answer

How to remove the inside left side front door


Snap out two door pull strap retaining screw covers. Remove screws.
Remove screws on front, rear and center of front door trim panel.
Using the Trim Pad Removing Tool or equivalent, pry the trim panel retaining clips from the door inner panel.
These are plastic so be careful you can use a pair of needle nose pliers if you don't have a trim tool.Just start at bottom of door panel and work your way around and up.

Mar 06, 2009 | 1997 Lincoln Town Car

1 Answer

2001 town car - air bag compressor


It's located under the air cleaner housing on the drivers side. After removing the housing there is a round plastic cover to remove and it is under that.

Dec 02, 2008 | 2001 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...