Question about 1996 Suzuki Swift

Open Question

Coolant coming from timing belt cover - 1996 Suzuki Swift

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a timing belt with a 2.4ltr motor?


Lift the car on lift and remove right tire . Remove front engine mount on the timing cover. Remove timing cover. Align the top timing mark on camshaft to the mark on back cover. Crankshaft will align automatically. Lose the belt tensioner and remove the belt.
I will suggest to replace the water pump and the seal on the camshaft and crankshaft. Install the belt and turn by hand crankshaft twice. make sure the marks align again. Install the cover, mount,serpentine belt.refill coolant. Bleed the system and run the engine till warm and radiator fan start. Cool and check the coolant level again.
good luck

Jun 13, 2014 | 1998 Plymouth Breeze

1 Answer

The water pump is not working how to fix it


Changing water pump invovles : remove the under cover, draining coolant, remove upper and lower radiator hoses, resservior tank hose, fresh air duct remove engine fan and shroud together loosen altenatormounting bolt and adjustment bolt remove altenator belt and fan pully, remove the 3 fan brakett assembly bolts and brackett assembly, remove the upper and lower timing belt covers . Turn crankshaft so #1 cylinder is at TDC then loosen timing belt tensioner lock bolt and pry tensioner away to loosen belt retighten tensioner lock bolt, remove and inspect timing belt as now is the time to replace bad or worn belt remove the water pump bolts and then same the coolant pump is the plate with the timing belt tensioner and idler pulley and a cogged gear at lower right. clean mating surfaces install in reverse order tighten coolant pump bolts to 16 ft-lb and tihgten tensioner bolt to 32 ft-lb coolant capacity about 7 quarts. be ecofreindly dispose of coolant according to local laws

Jun 01, 2011 | 1998 Kia Sportage

1 Answer

How does the timing belt cover come off the 1998 Mazda B2500 "


REMOVAL & INSTALLATION

2.3L/2.5L Engines
(see Figure 1 - click over pic for zoom)

zjlimited_982.jpg

Fig. 1: Timing belt cover on the 2.3L/2.5L engine

  1. Disconnect the negative battery cable.
  2. Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.
Always turn the engine in the normal direction of rotation. Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner.
  1. Drain cooling system. Remove the upper radiator hose as necessary. Remove the fan blade and water pump pulley bolts.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Loosen the alternator retaining bolts and remove the drive belt from the pulleys. Remove the water pump pulley.
  2. Loosen and position the power steering pump mounting bracket and position it aside.
  3. Remove the timing belt outer cover retaining bolts and any interlocking tabs and remove the cover.
To install:
  1. Install the timing belt cover.
  2. Install the water pump pulley and fan blades. Install upper radiator hose if necessary. Refill the cooling system.
  3. Position the alternator and drive belts, then adjust and tighten it to specifications.
  4. Connect the negative battery cable.

Hope helps (remember to rated this answer).

Apr 06, 2011 | 1998 Mazda Pickup

1 Answer

1999 2.3 supercharged mazda millenia s; need user/repair manual and help fixing/replacing water pump


Hello, Here are the steps for removing and reinstalling your water pump.
Removal
  1. Disconnect the positive battery cable.
  2. Put a drain pan under the radiator and drain the coolant. Drain the coolant out via the drain plug on the radiator.
  3. When drained close the drain plug.
  4. Put another drain pan under the timing belt cover.
  5. Now you need to remove the timing belt cover.
  6. Use a ratchet and remove all the bolts to the time belt cover.
  7. Remove timing belt cover.
  8. When you get the cover off remove the timing belt.
  9. ***NOTE*** due to the time, labor and potential cost of replacing the water pump and the fact that the timing belt is right there it is recommend to put a new timing belt on during the installation process.
  10. Remove the bolts that secure the coolant inlet pipe with a ratchet.
  11. Remove the pipe and gasket.
  12. Remove the belt and idler pulley attached to the water pump. Don't get and coolant or grease on it.
  13. Now you need to remove the mounting bolts from the water pump with a ratchet.
  14. Remove the pump.
  15. Inspect the seating of the gasket real well.
  16. Remove all the crud off it with a lint free rag, I repeat lint free rag.
Now to install the new water pump
  1. Install the new water pump with the new gaskets provided. Never reuse the old gaskets.
  2. Install mounting bolts and torque them at 14-18 foot pounds.
  3. There is a bolt that will connect the alternator bracket to the water pump that needs to be torqued at 23-38 foot-pounds.
  4. Reinstall the idler pulleys and tighten down with your ratchet.
  5. Replace the gasket for the coolant intake pipe with the new gasket.
  6. Now torque the remaining bolts to 14-18 foot pounds.
  7. Slide the [hopefully new] timing belt back.
  8. Reattach the timing covers.
  9. Tighten them bolts with your ratchet.
  10. Use a mix of 50% water and 50% antifreeze and fill up the radiator and overfill.
  11. Squeeze the radiator hoses a few times to get the air out of the hoses.
  12. Hook your battery back up.
  13. Start the car and let it heat up to full running temperature, with the heat on and check for leaks.
  14. Now top off the coolant level again.
  15. Go for a short drive.
  16. Reinspect for leak.
  17. End of job.
Regards, Tony

Mar 24, 2011 | Mazda Millenia Cars & Trucks

3 Answers

Leaking coolant.. its hard to see where it is coming from.. it leaks out heavily when car is cranked,, it looks like it is comin from right behind the belt drive (the bigger one) is that the water pump?


This does sound like your water pump is leaking, or your head gasket has busted on the outside edge. I would check the water pump first, as it is fairly common for the seal to bust and leak coolant from the water pump.

Feb 16, 2011 | 2004 Pontiac Grand Prix

1 Answer

Timing belt removal 94 mercury villager


Hi, Disconnect battery ground cable, then drain coolant. Remove accessory drive belts. Remove A/C compressor drive belt idler pulley (tensioner) bolts, then idler pulley (tensioner). Remove upper radiator hose bracket bolt. Loosen two upper radiator hose clamps, then remove upper hose and bracket. Remove coolant bypass hose between thermostat housing and intake manifold coolant outlet. Disconnect main wiring harness from upper front cover (timing belt) cover, then remove eight upper timing belt cover bolts, then the upper cover, Fig. 20. Raise and support vehicle. Remove right front wheel and tire assembly and splash shield. Use strap wrench tool No. D85L-6000-A, or equivalent, to hold water pump pulley while removing water pump pulley bolts. Remove water pump pulley from water pump. Remove crankshaft pulley. Remove five lower timing belt cover attaching bolts and the cover. Rotate crankshaft in a clockwise direction to align crankshaft and camshaft sprocket timing marks, Fig. 21. If timing belt is to be reused, mark direction of rotation. Loosen timing belt tensioner nut, then remove timing belt. CAUTION: With timing belt removed, avoid turning camshaft or crankshaft. If movement is required, exercise extreme caution to avoid valve damage caused by piston contact.
Take care

Jul 24, 2010 | 1995 Mercury Villager

1 Answer

Coolant leak after a long run only, fan cuts in when engine is switched off and then coolant leaks from the timing belt cover area, have changed the pressure cap. car is a fiesta 2003 zetec 1.4


oh b*m! its a leaky water pump,,,that wont be cheep to fix,,,cam belt must come off so have a new belt fitted at the same time,,ok,,,it saves money in the long run?

Jun 29, 2010 | 2004 Ford Fusion

2 Answers

I need 2004 Hyundai XG350L Service/repair Manual


3.5L Engine

Remove or disconnect the following:
  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Feb 10, 2010 | 2004 Hyundai XG350

1 Answer

HOW TO REPLACE A WATER PUMP


Sonata 2005 2.4 DOHC
REMOVAL 1. Drain the coolant and disconnect the coolant pump inlet pipe. 2. Remove the drive belt and engine coolant pump pulley. 3. Remove the timing belt covers and the timing belt tensioner. 4. Remove the engine coolant pump mounting bolts, then remove the alternator brace. 5. Remove the engine coolant pump assembly from the cylinder block.

6909bef.gif

Aug 11, 2008 | Hyundai Sonata Cars & Trucks

1 Answer

Water pump


1. Drain the coolant and disconnect the coolant outlet pipe connection hose from the coolant pump. 2. Remove the drive belt and engine coolant pump pulley. 3. Remove the timing belt covers and the timing belt idler. 4. Remove the coolant pump mounting bolts, then remove the generator brace. 5. Remove the coolant pump assembly from the cylinder block. See an exploded view:
d0ab616.gif

Jun 27, 2008 | 1997 Hyundai Elantra

Not finding what you are looking for?
1996 Suzuki Swift Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...