Question about 2004 Ford Crown Victoria

1 Answer

Positraction axle seal - 2004 Ford Crown Victoria

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 95 Answers

ON THESE CARS THE AXLES ARE SOFT WICH MAKES A WEAR MARK ON THE AXLE WHERE IT CONTACTS THE OUTER BEARING WICH MAKES THE SEAL LEAK THERE WAS A DEALER RECALL ON THIS PROBLEM YEARS AGO.I HAD TO REPAIR THE SAME PROB ON MY 2003 GRAN MARQUIE

Posted on May 30, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear axel wheel bearing and seal on 2006 jeep liberty renegade 4wd


its not just the seal.... i bet,

99% of seals that fail are , the bearing is allowing , out of spec.

moving in the axle

so when doing all that hard work ? we check this first.

do you know all cars have this book, called the FSM.

and all show you how this is done? every one.

factory service, manual,



but hark, we have them on line now.

alldata.com (15 BUCKS)



I BET PART 2 AND 3 ARE BAD HERE

http://www.factorychryslerparts.com/showAssembly.aspx?ukey_assembly=533119&ukey_product=4240348



THE REAL CD IS ABOUT $130 (instant payback first job done by you) see?



https://www.techauthority.com/en-US/Pages/Home.aspx





eg.

Removal & Installation


  1. Before servicing the vehicle, refer to the Precautions section.


  2. With vehicle in neutral, position vehicle on hoist.


  3. Remove differential housing cover and drain lubricant.


  4. Rotate differential case so pinion mate shaft lock screw is accessible. Remove lock screw and pinion mate shaft from differential case.


  5. Push axle shaft inward and remove axle shaft C-lock from the axle shaft.


  6. Remove axle shaft from side gear and axle tube.


  7. Remove axle shaft seal from axle tube with a seal pick.


To install:



  1. Remove any old sealer/burrs from axle tube.


  2. Coat new seal lip with axle lubricant and install seal with a seal driver.


  3. Lubricate bearing bore and seal lip with gear lubricant.


  4. Install axle shaft through seal, bearing and engage into side gear splines.


  5. Install C-lock in axle shaft end, then push axle shaft outward to seat C-lock in side gear.


  6. Install pinion mate shaft into differential case and through thrust washers and differential pinions.


  7. Align hole in shaft with hole in the differential case and install lock screw with Loctite on the threads. Tighten lock screw to 8 ft. lbs. (11 Nm).


  8. Install the differential cover.


  9. Install rear brake components.

Sep 06, 2014 | 2006 Jeep Liberty Renegade

2 Answers

Have a 1997 plym voyager 2.4 auto trans with a trans leak where driver side axle bolts to tranny


the axle just slides in at that spot there is a seal there you will need to pull axle out and replace seal

Mar 12, 2011 | Plymouth Voyager Cars & Trucks

1 Answer

How do you change the rear wheel bearings on a 2004 chevy express 1500 van?


Axle Shaft Bearing & Seal Removal & Installation To Remove:
  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Oct 18, 2010 | 2004 Chevrolet Express

1 Answer

4wd is it working properly or not


No. Power will transfer to the wheel with the least amount of traction unless the differential is a limited slip diff. You likely have limited slip (Positraction) in the rear diff so both wheels will spin. The front axle doesn't have posi so only one wheel will spin. (3 wheels spinning)

Apr 10, 2010 | 1994 Isuzu Trooper

1 Answer

2005 single axle F-350


Yes you will need to pull the axle to get that seal out. You will need to pull tire open punkin or gear case there will be a C clip holding the axle inplace pull this out and very carefully slide the axle out the seal is in the axle housing

Apr 08, 2010 | 2005 Ford F 350 Super Duty

2 Answers

Can't remove c-clips off rear axles in a 1995 chev positraction rear end


need to have someone help by pushing in on axle then remove the clip than same for other side

Oct 13, 2009 | 1995 Chevrolet Impala

2 Answers

I cant remove a rear axle seal to a 1999 honda passport


Axle bearing and seal are made together. It is pressed on axle.

Aug 18, 2009 | 1999 Honda Passport

2 Answers

Rear wheel bearing


SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Apr 10, 2009 | 2004 Ford GT

1 Answer

1995 jeep grand cherokee right rear axle bind in sharp turn


If you have a positraction rear differential, the clutches may be sticking. If so, change lube and use an additive for posi rears. After changing lube, go in a parking lot and make a series of tight turns in both directions to get plates to separate and resume normal function. Before changing lube check to make sure it is full and that no suspension components in the rear are broken or loose that could cause rear to move and drag one wheel when turning.

Feb 24, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Ford Crown Victoria Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...