Question about 2008 Ford F 250 Super Duty 4WD

1 Answer

Oil can light stays on

Oil has been change but light stays on when idling or three days after oil change

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Ford Expert
  • 496 Answers

Run a Scan on it first but also check the Oil Pressure Sending Unit and the actual Oil Pressure with a Mechanical Gauge. You may have a bad oil pump.

Posted on May 23, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Check engine light came on, checked oil and it was fine. I was looking at my gauges, and the oil pressure seemed really off. It's normally around 20 at idle which is normal then its normally at 40 when...


it could be as simple as a bad oil pressure, or it could be a bad engine. If the oil pressure was good before the oil change maybe the oil filter might be the problem

Aug 02, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Oil light blinking


there is always the possibility that you really have low oil pressure when you get this light, at idle the engines oil pump produces the least pressure and if there are problems then that is when it shows up, so have the oil pressure tested by a shop with a mechanical test gage, if the oil pressure is within spec then replace the oil pressure light sending unit on the engine, I don't recommend you drive this until u are sure of the pressure, u can SEVERELY damage the engine is the pressure is really low.

Jun 23, 2010 | 1993 Honda Accord

1 Answer

Blinking oil light on 2003 Mazda Protege. Changed oil and oil filter as well as oil sensor. Light still blinks when the car is idled up.


You need to reset your change oil warning light. To do this, turn the ignition key to on but do not turn over the engine. Then rapidly push down the gas pedal three times. This will reset the system and turn off the blinking light. Then when you drive another 3000 miles, that light will once again tell you it is time to have your oil changed. J.

Jun 20, 2010 | 2002 Mazda Protege

4 Answers

Oil light stays on


You need to put the key on and push the gas pedal to the floor three times within five second to reset the oil life light.Some g.m.'s have a reset buttom in the fuse panel that needs to be pushed first and some don't.Check the owners manual under change oil for your specific year car.

Oct 21, 2009 | 2003 Chevrolet Impala

1 Answer

How much is oil pressure supposed to hold


10 lds at idle when cold but after buildup of preasure. This will change with oil temp. r.p.m. and engine wear. Low oil preasure is usually the result of engine wear but not a fault in an engine. If the oil light fliker's at idle when warm then the engine is excessavely worn and will soon cause problem's if the oil light stays out when warm at idle then its nothing to worry about.

Oct 11, 2009 | 1996 Isuzu Hombre

3 Answers

OIL LIGHT STAYS ON AFTER OIL CHANGE AND I DON'T HAVE THE OWNERS MANUAL TO GET THE RESET CODE


Try this. With the key on and the engine not running push the gas peddle to the floor and release it three times then hold it to the floor until the oil light flashes. This should reset the oil indicator light. It should not take more than about 20 or 30 seconds.Good luck.

Jun 23, 2009 | 2005 Chevrolet Trailblazer Ext

1 Answer

Oil pressure for my jeep 2002 wrangler


As long as it's not going down, and the engine isnt knocking, you do not have a terrible problem. I have used marvel oil in ones that do this and most times it clears up. If not, change the pressure switch. (Takes a few days before it get's better with mm oil)

Apr 22, 2009 | 2002 Jeep Wrangler

1 Answer

Rough idle / varying oil pressure when accelerating


Ok not to keen on newer vehicles actually prefer the carburated ones, but oil pressure is supposed increase on your gauge when accelerating. If it wasn't going up before and just staying at 40 the needle might have been stuck. But idle should be 40 lbs and when you work the moter (reving or driving down the road) the guage should show an increase for every 1000 rpm above idle. Second if you can get a hand held scanner (bought mine off ebay for $30) check for any codes in your computer you will probably find that you either have a bank running wrong or some other sensor that needs to be changed. I'd go with getting my own scanner it saves alot of money and time, garages make their money here.

Jan 03, 2009 | 2005 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...