Question about Volkswagen Cars & Trucks

Open Question

Fly wheel torque settings agy engine - Volkswagen Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: torque settings for pressure plate and fly wheel

the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Posted on Nov 22, 2008

Ad
alicantecoli
  • 22265 Answers

SOURCE: need to know the torque settings

put some locktight on the flywheel bolts and make sure they are tight by using a impact gun or jam a screwdriver into ringear and a bellhousing bolt as fulcrum and then pull bolts up with a big snap on knuckle bar and go round twice 1/2 inch drive---clutch use a 3/8 socket set and dont over tighten go round at least 3 times and dont forget to put copper grease on the spigot shaft splines .And remember to top the gearbox oil up with EP90 ,and lightly grease the new rear end oil seal you have obviously changed .

Posted on Apr 05, 2009

iambanshee74
  • 3489 Answers

SOURCE: I am putting a 99

The torque converter is not all the way in the transmission. Pull the transmission back out(unfortunately) and you will need to shake and wiggle while lightly pushing the torque converter into the transmission. Once it goes over the splines for the pump, you will know and the space between it and the transmission housing will be minimal.

Posted on May 13, 2010

Testimonial: "Thank you for responding. I ended that conversation because I was already in the middle of another. I did make sure the torque converter was all the way in. I could have come out while i was installing the tranny."

1125rguy
  • 40 Answers

SOURCE: hi i need the torque

torquespecs.com if not there there are several sites like that one that list any car u can dream of.good luck

Posted on Feb 04, 2011

  • 1 Answer

SOURCE: I am busy with an

timing marks

Posted on May 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All specs on assembly of engin


How can we do that ?we do not know make,model year engine size

Mar 12, 2016 | Cars & Trucks

1 Answer

I have a 94 Hyundai Excel. I am replacing the clutch but can't find the torque settings anywhere.


clutch/flywheel torque settings - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/...accent/146383-clutch-flywheel-torque-setti...

Aug 2, 2012 - 3 posts - ‎2 authors
Im after the torque setting for the clutch and fly wheel for a lc 2000 accent with the dohc 16v engine. cheers.Missing: .94

Torque value head bolts 1994 hyundai excel 1.5l - Fixya

www.fixya.com/cars/t12339610-torque_value_head_bolts_1994_hyundai
Apr 7, 2012 - SOURCE: torque settings for a hyundai accent 1500 1998. cylinder ...SOURCE: how d i change a clutch in a hyundai excel 1994. Hi first lift the ...

Flywheel & Pressure Plate Torque Specifications? - Hyundai ...

www.hyundaiaftermarket.org > ... > Engine, Intake, Exhaust

Dec 19, 2015 | Hyundai Cars & Trucks

1 Answer

Does a torque converter for a 1989 ford bronco trwo have antyhing to do with a fly wheel


The torque converter bolts to the flex plate at the rear of the engine. It supplies the link between the engine to the transmission.

It's known as a "Flex Plate" and not a "Fly Wheel". The flywheel is use on a standard transmission.

May 14, 2010 | 1989 Ford Bronco II

2 Answers

How do i change the starter on a 96 century


If it's the 3.1 or the newer 3100 the starter should just be a couple 13 and 15mm bolts. Plus the nut for the cable. Hope this helps.

Jul 13, 2009 | 1996 Buick Century

1 Answer

How to unbolt torque converter on a 1kzte engine and to remove engine


there is a cover at the bell housing of the gearbox! remove its bolt then access the thin fly wheel! there are bolts that attach it to the torque converter! remove all as you rotate the fly wheel! pretty simple!

Jun 16, 2009 | 1996 Toyota 4Runner

1 Answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper


diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

Jan 03, 2009 | 2001 Isuzu Trooper

1 Answer

Torque settings for pressure plate and fly wheel


the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Nov 22, 2008 | 1995 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77201 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...