Question about 2001 Lincoln Town Car

Open Question

How to remove the cylinder heads on a 2001 lincoln town car 4.6

How to remove cylinder heads

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

Ad
Mr BrokRench
  • 1623 Answers

SOURCE: heat wont work 2001 lincoln town car cartia

Hello Callahan5922....this sounds like a stuck blower motor resistor. I assume the blower won't function in the a/c mode either? If you have a digital multimeter you can check this. I believe it's fuse #2....if the digital indicator goes up or down when you increase or decrease the fan speed thats good. Locate the blower motor resistor....you wil find it located on the fire wall behind the right valve cover hiding behind the heater hose, it's about the size of a cigarette pack. With the engine off, and key in on position, turn the A/C on High, and rap a tap tap tap on the resistor. You might be suprised when the blower motor takes off a runnin,
I hope this is the answer you need and i was able to help solve this for you. Good luck...

Posted on May 13, 2009

  • 1 Answer

SOURCE: 2001 lincoln town car winshjield wiper

where is the fuse box for my 2001 lincoln towncar looking for windshield wiper fuse because they wont turn on what so ever

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of tool do you need to change out the license plate bulbs on 2001 Lincoln town car?


Gently lever off the plug on the liner, and twist them out.

It will be the same as this video.

Lincoln ls 2001 license plate bulb

Jan 26, 2016 | 2001 Lincoln Town Car

1 Answer

I have a 03 lincoln town car with the 4.6l v8 and cant figure out how to remove the cover that covers the engine


At the rear center or the cover is 1/4" square drive headed bolt -remove using your 1/4" ratchet with a 1/4" extension . lift rear of cover and push cover forward off the two horizontal tabs facing forward in front. reattach in reverse order.

Feb 22, 2015 | 2003 Lincoln Town Car

1 Answer

I have a 2001 Lincoln Town Car with codes p1074 and p1074 and I was advised by a mechanic to replace the engine is that true?


Not sure on the code, it could be PO174. It may be an O2 sensor or problems with the intake and/or cyl heads.
I would make sure on the code and get a second opinion.

Jun 23, 2012 | 2001 Lincoln Town Car

1 Answer

Cylinder 5 placement?


if you have the V8 gas engine, the cylinders on the passenger side from front to back are #1 #2 #3 #4 the cylinders on the driver side are from front to back #5 #6 #7 #8. if you have a V6 gas engine the cylinder placement is passenger side from front to back #1 #3 #5 the cylinders on the drivers side are from front to back #2 #4 #6. if you have a diesel V8 engine the cylinder placement is passenger side from front to back #1 #3 #5 #7 drivers side from front to back #2 #4 #6 #8 and last but not least if you have the V10 the cylinder placement is passenger side from front to back #1 #2 #3 #4 #5 and driver side from front to back #6 #7 #8 #9 #10.

Dec 24, 2010 | 2001 Lincoln Town Car

1 Answer

How can i remove a ignition lock cylinder from a 98 lincoln town car


Ford vehicles usually have a small hole under the ignition lock cylinder that allows access to the release for the cylinder. I assume Lincoln has a similar setup. Turn the ignition to on and locate the small hole in the steering column trim, use a long thin punch and stick it in the hole depressing the release. You should be able to gently pull the lock cylinder out now.

Sep 05, 2010 | 1998 Lincoln Town Car

1 Answer

Where is the blower resistor located on a 94 lincoln town car?


On the firewall by the back of the passenger side cylinder head.

Mar 14, 2009 | 1994 Lincoln Town Car

2 Answers

Changing turn signal switch 1986 lincoln town car.


shouldn't have to... just remove the cowling surrounding the steering column between the steering wheel and the dash to give you access to the part

Feb 24, 2009 | 1986 Lincoln Town Car

1 Answer

2001 town car - air bag compressor


It's located under the air cleaner housing on the drivers side. After removing the housing there is a round plastic cover to remove and it is under that.

Dec 02, 2008 | 2001 Lincoln Town Car

Not finding what you are looking for?
2001 Lincoln Town Car Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5530 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...