Question about 1999 Ford Ranger SuperCab

Open Question

Need to replace water pump gasket and need he proper torque specs

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

  • 207 Answers

SOURCE: Head gasket torque specs

Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Posted on Apr 30, 2009

mkv0525
  • 358 Answers

SOURCE: what are specs for water pump bolts for 2001

Home | Account | Contact ALLDATA | Log Out | Help ALL TUNE & LUBE DDG AUTOMOTIVE Select Vehicle | New TSBs | Technician's Reference Component Search: Conversion Calculator 2001 Ford Taurus V6-3.0L VIN 2 Flex Fuel Vehicle Level Specifications Mechanical Specifications Water Pump Water Pump Water Pump Notes Engine Front Cover and Water Pump Assembly 25 Nm (18 lb-ft) © 2009 ALLDATA LLC. All rights reserved. Terms of Use

Posted on Jun 10, 2009

  • 122 Answers

SOURCE: need cylinder head gasket torque specs.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Posted on Sep 18, 2009

  • 85 Answers

SOURCE: NEED FORD 2.2l head gaskets torque chart

Tighten the head bolts 29 to 32 ft lbs , then tighten again to 59 to 64 ft lbs

Posted on Apr 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for the water pump housing for a 1998 cadillac deville


That's a tough one Tom. I don't think that spec is in the standard shop manual. If the dealer won't tell you, you might check the size and grade # of the bolts and then check the generic torque vs size chart often found in the front of most shop manuals. Use sealant on threads. Sorry to not be more help.

Dec 18, 2014 | Cadillac Cars & Trucks

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

1 Answer

1993 Dodge Dakato Front pump Torque specs?


just replace and save your self the headache

Jun 14, 2012 | 1993 Dodge Dakota

2 Answers

How can I replace the water pump on a 2004 Grand Prix GTP superchargered?


WELL YOU NEED TO DRAIN COOLANT SYSTEM.PLACE A LARGE DRAIN PAN UNDER THE RADIATOR TO CATCH COOLANT WHILE DRAINING RADIATOR.ONCE ALL COOLANT DRAINED OUT.REMOVE DRIVE BELT.REMOVE WATER PUMP PULLEY.REMOVE POWER STEERING PUMP AND MOVE IT ASIDE.THEN REMOVE WATER PUMP.MAKE WATER PUMP MOUNTING SURFACE CLEAN THEN INSTALL NEW WATER PUMP AND GASKET IN PLACE.IF WATER PUMP GASKET IS PAPER TYPE PUT GASKET SEALANT ON BOTH SIDES OF THE GASKET.IF YOU HAVE RUBBER GASKET DONT USE NO GASKET SEALANT.INSTALL NEW WATER PUMP TORQUE LONG BOLTS TO 25 FT LBS AND TORQUE SHORT BOLTS TO 16 FT LBS.TORQUE WATER PUMP PULLEY TO 115 INCH POUNDS.TORQUE POWER STEERING PUMP BOLTS TO 25 FT LBS.THEN INSTALL DRIVE BELT.FILL THE COOLANT SYSTEM.START THE VECHICLE AND CHECK FOR LEAKS.

Mar 25, 2011 | Pontiac Grand Prix Cars & Trucks

2 Answers

Torque specifications for head bolts 1995 Jetta 2.0


First pass, torque them to 30 Ft Lbs working from the center outward. Then go back again and torque them to 75 Ft Lbs.

Feb 21, 2009 | 1995 Volkswagen Jetta

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Water pump replacement procedure 2005 2500 dodge with cummins diesel


take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Aug 22, 2008 | 2005 Dodge Ram 2500 Truck

1 Answer

Replacing head gasket


http://www.haynes.com/

best bet will be to purchase the haynes manual for proper specs and torque ratios

Jun 12, 2008 | Mitsubishi Passenger Cars & Trucks

3 Answers

Replace water pump


First you must drain the coolant. Remove powersteering pump[keep hoses connected)this is just to make room for water pump removal so just sit it off to he side.Loosen the the water pump pulley mounting bolts, remove the drivebelt,remove the pump pulley. Remove the pump mounting bolts and pul the pump from engine.Install every thing in reverse ,but be sure to clean the mating surface of old sealer and gasket first, also be sure to use RTV gasket sealer on engine side of the new gasket.Be sure not to over/under tighten the bolts the torque specs. are 22 to 29 for the long bolts and 96 to132 for short bolts and 108 to 132 ft lb for the pulley bolts.

May 15, 2008 | 1994 Oldsmobile 88

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...