Question about 2005 Mercury Montego Luxury
The blower to ac/heater stays on even is we push off and iit blows high
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
remove the trim panel below the glove box and you will see the blower motor,just to the left of it you will see a 4 wire connector plugged into the case. This is the blower motor resistor,this is what you need to replace.
Posted on Feb 12, 2009
Go to a automotive store and tell them you have a 2005 Mercury Montego and what engine it has if there is more then one model and get an oil filter and the oil. Put the car up on ramps and secure it making sure it won't roll back or fall while you are under it. get under the engine and look for the oil pan which should have a bolt in the bottom of it where you can drain the oil. Drain the oil in a proper container and then put the drain plug back in the pan. Then find the oil filter and unscrew it and remove it.. It could be full of oil so watch out and make sure the pan is underneath the filter. Wipe the base where the oil filter screws on and make sure the gasket from the old filter is not still on the engine. Get your new filter and take your finger and put it in one of your new containers of new oil and spread that on the gasket of the new filter. Screw on the filter until the gasket touches the base and then turn only a little more then a 1/4 to 1/2 turn tops. Do not over tighten the filter. Find out what oil the vehicle needs (probably 5-30) and look for the oil cap on a valve cover under the hood. It probably takes 5 quarts but check for sure in your manual or ask when you are at the automotive store. Put the oil in and put the filler cap back on. Now go start the vehicle and make sure you have oil pressure by either the oil pressure guage showing pressure or the oil pressure idiot light goes off and while running check under the car for any signs of leaks. If no leaks then back the car off the ramps and shut the car off on a level surface. Let it sit 10 minutes and check for leaks underneath the car and check the oil dipstick to make sure the proper level of oil is in the engine. Then you are set.
Always check your air filter when changing oil to make sure it is clean as that helps your engine run better and you save gas in the process. Good luck
It is also best to change oil when your engine is warmed up as well.
Posted on Mar 28, 2009
SOURCE: ac blower motor
Check fuse supplying fan is not blown,
Check blower control switch is operating OK,
Check relay controlling fan is operating OK,
Check variable speed resistor pack is not faulty (the resistor pack is usually located in the blower ducting, in the blower airflow),
Check blower motor ground connection is not missing.
Posted on Aug 13, 2009
SOURCE: 2003 mercury grand marquis LS
The blend door is stuck in cold position. That usually happens because the blend door actuator has failed.
You will need to test and replace the blend door actuator.
To replace the actuator you will need to take apart the dash and remove completely the instrument panel,d isconnect the connector, remove the four screws, remove the temperature blend door actuator and replace it.
The replacement is not a job for beginners, since you have to take apart the dash to access the actuator.
Posted on Nov 18, 2009
Tips for a great answer:
Aug 05, 2016 | Cars & Trucks
Feb 27, 2015 | 2011 Nissan Titan Crew
Nov 02, 2012 | 2002 Ford Taurus
Jan 15, 2010 | Mercury Montego Cars & Trucks
Dec 21, 2009 | 1995 Mercury Tracer
Jun 03, 2009 | 1994 Cadillac DeVille
Oct 09, 2008 | 2007 Mercury Grand Marquis GS Sedan
Jul 14, 2008 | 2003 Nissan Pathfinder
156 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: