Question about Cars & Trucks

1 Answer

How to get ring off finger with too large a knuckle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,854 Answers

There is only one solution that will not be painful but you could try placing fat/ oil on the finger around the ring and pull the skin back away from the knuckle to reduce the tendency of the skin to bunch up before the ring and stop the ring sliding off . Other than that use a small triangle file and file a groove across the band ( at an angle ) or angle cutters to nip the band . Unfortunately you will have to get the ring repaired by a jeweller but if you want the ring this is an advantage as a piece can be put in to enlarge the ring size.

Posted on Feb 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Outer race of wheel bearing is stuck in knuckle. How do I remove?


You can hammer it out, or use a hydraulic press

Mar 26, 2013 | 1997 Toyota RAV4

1 Answer

How do i get the rear wheel bearing off of my 2001 lincoln ls


You have to remove the aluminum wheel
knuckle & then a large snap ring & press
out the bearing

Mar 10, 2013 | Lincoln LS Cars & Trucks

1 Answer

Bearing came apart, outside still in hub how do i get it out? does it come out the front or back of the hub?


This bearing come out from the back. The knuckle must be removed from the strut and the lower control arm ball joint. The hub comes out the front. The bearing comes out the back. There is a snap-ring (large one) on the inside of the knuckle which must be removed before you can press out the bearing inner race (you'll need a hydraulic press and proper sized dyes and support plates).

ILLUSTRATION:

ghost45_23.jpg

Aug 27, 2011 | 2001 Hyundai Elantra

1 Answer

How do i change front wheel bearing on a ford focus st2


SECTION 204-01: Front Suspension 2000 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/18/2003 Wheel Bearing
Special Tool(s) 15064.jpg Installer, Wheel Hub Bearing Cup
204-023 (T73T-1217-A) 21171.jpg Remover/Installer, Bushing
204-180 (T93P-5493-A) 15064.jpg Installer, Drive Pinion Bearing Cup
205-140 (T80T-4000-F) 205153.jpg Adapter for 303-224 (Handle)
205-153 (T80T-4000-W) d84l1123a.jpg Puller, Bearing
205-D064 (D84L-1123-A) 21217.jpg Installer, Wheel Speed Sensor Ring
206-054 (T93P-20202-A) Removal
  1. Remove the wheel knuckle. For additional information, refer to Wheel Knuckle in this section.
  1. NOTE: When removing the hub from the wheel knuckle the bearing will be destroyed. The bearing inner ring will be on the hub and the bearing outer ring will be in the wheel knuckle.
    Using the special tools, remove the wheel hub from the wheel knuckle.
    e0027601.jpg
  1. ani_caut.gif CAUTION: The special tools must be used to prevent damage to the hub. If the hub is damaged a new hub must be installed.
    ani_caut.gif CAUTION: Do not use heat to remove the bearing inner ring.
    Using the special tools, remove the bearing inner ring from the wheel hub.
    e0027602.jpg
  1. Remove the circlip from the wheel knuckle.
    e0002134.jpg
  1. Install the old bearing inner ring.
    1. Install the bearing cage on to the bearing inner ring.
    1. Install the bearing cage and inner ring assembly to the wheel knuckle.
    w1401022.jpg
  1. Using the special tools, remove the bearing outer ring from the wheel knuckle.
    e0027603.jpg
Installation
ani_caut.gif CAUTION: Avoid any impact on the wheel speed sensor ring.
ani_caut.gif CAUTION: Make sure the wheel speed sensor ring is clean.
ani_caut.gif CAUTION: Avoid any contact between the wheel speed sensor ring and a magnetic surface.
  1. ani_caut.gif CAUTION: Make sure the wheel bearing is installed into the wheel knuckle with the wheel speed sensor ring, colored black, at the wheel speed sensor end of the wheel knuckle.
    Using the special tools, install the new wheel bearing to the wheel knuckle.
    e0027604.jpg
  1. NOTE: Make sure the circlip does not cover the wheel speed sensor.
    Install the circlip to the wheel knuckle.
    e0002134.jpg
  1. Using the special tools, install the wheel hub to the wheel knuckle.
    e0027605.jpg
  1. Install the wheel knuckle. For additional information, refer to Wheel Knuckle in this section.

Apr 05, 2010 | 2000 Ford Focus

1 Answer

2004 silverado 4x4 2500 left front wheel bearing


  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Jan 19, 2010 | 2004 Chevrolet Silverado 2500 Crew Cab

1 Answer

How install halfshaft axle on a ponitac g6


Do you have them off already? If not jack car block up at FRAME put in neutral pull wheel remove tie rod nut remove axle nut remove ball joint bolt from lower knuckle seperate knock axle out from knuckle don't DAMAGE axle threads pop axle out from trans large prybar from axle to trans should pop out held in with snap ring install reverse or what you did

Oct 09, 2009 | 2006 Pontiac G6

3 Answers

How to replace a transmission output seal 93 buick lesabre


you have to raise vechicle.use jack stands.block rear wheels.apply parking brake.when loosen axle nut.its more easier to leave wheel on.let vechicle weight hold wheel from turning while you loosen axle nut.you need to get a 1/2 break bar or large ratchett wrench with a deep socket .you need to buy socket use to remove axle nut a regular socket would probably break.when you remove the axle nut.remove brake caliper and brake pads.set them aside dont disconnect brake caliper.get a piece of wire to hang it out the way.dont use brake hose.could damage it. remove brake caliper support bracket then the rotor.get a hub removing tool remove hub.then loosen hub and bearings bolts .then remove shield hub and bearings assembly with O-ring.disconnect ball joint from steering knuckle using the proper tool.remove the halfshaft assembly and tap the seal from the steering knuckle.remove the steering knuckle from the hub.now that drive axle out the way.get the seal removing tool.its a flat tool with two hooks on it.to pry seal out transmission.or you can use a small chisel to clapse the seal but be careful dont damage the seal housing.when installing new seal coat it with transmission fluid.drive it in using a large socket.if you are reusing same axle replace circlip on the end of it.now putting back together.install a new hub and bearing seal in the steering knuckle with a seal installer tool .install steering knuckle to the strut.lubricate the hub and bearings with grease.install halfshaft.connect ball joint to the steering knuckle .install a new O-ring around the hub and bearing assembly.install hub and bearing assembly into the steering knuckle.tighten bolts to 75 ft lbs.install rotor then brake caliper support bracket bolts 120 to148 ft lbs.this is mounting bracket bolts only not the caliper bolts to brake shoes.put brake shoes and caliper back on torque 38 ft lbs.install shaft washer the axle nut to 180 ft lbs.tighten much as you can.before setting car on ground.to torque it to 180 ft lbs place car wheel back on set it down so the car weight keep wheel from turning.i hope this information works out for you good luck.and work safe.

Jun 27, 2009 | 1993 Buick LeSabre

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

1 Answer

Roaring in front end


Bearing is pressed into the knuckle,hub is pressed into bearing.You will need to take knuckle off,remove large snap ring & press out hub,then bearing.Hope this helps

May 03, 2009 | Saturn SL2 Cars & Trucks

2 Answers

Any help on replacing the drivers side cv joint


remove the large nut on the end of the axle, unbolt the strut from (tie it out of the way with bailing wire, avail from any hardware store) the steering knuckle, pull the steering knuckle out of the way while pushing the axle stub inward and out of the knuckle, once the axle is free of the steering knuckle the axle just snaps out of the transmission, this can really be a bear, but it does just snap in and out, it uses what is called an internal snap ring to retain it into the transmission, u might also want to replace the axle seal as it most likely will suffer damage when u pull the axle out.

Feb 10, 2009 | 2000 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...